5 lights 2 plants Black Rose :shock:

sallygram

sallygram

Well-Known Member
When I set up my room (after a 25 year hiatus), I almost took the reflectors off and went vert, I decided to hold off until I had a few good grows. Then I started to read some of your posts and figureing out surface area covered by light one night and ended up switching the whole flower room all around in mid grow. My next big change is going to be CMH. Thanks!
 
ttystikk

ttystikk

Well-Known Member
sallygram said:
When I set up my room (after a 25 year hiatus), I almost took the reflectors off and went vert, I decided to hold off until I had a few good grows. Then I started to read some of your posts and figureing out surface area covered by light one night and ended up switching the whole flower room all around in mid grow. My next big change is going to be CMH. Thanks!
Click to expand...
Skip the CMH and just go straight to LED. Even if you do it in stages.
 
gr865

gr865

Well-Known Member
ttystikk said:
I don't have to believe, I've proven it.
Click to expand...
TTy,
I have only used the CLW SS400 in a convention horizonal grow, pentration was lacking. I did do a 6 plants sort of SOG, flowered two week old clones in 4 gallon Hempy buckets. That was a better grow.
The heat sink, I think that is what it is called that DesertHydro posted,
headed in the right direction
.

Looks like that would be a good starting point.
Since I know very little about LED mechanics, and especially COB's, if I a correct the individual diodes are affixed to the heat sink. My LED lights are 5W x 80 lights, and it has is fan driven cooling.
Do you have a website with a simple tutorial on constructing an LED fixture. Would be interesting,
Just want to learn a bit about them.
GR
 
ttystikk

ttystikk

Well-Known Member
gr865 said:
TTy,
I have only used the CLW SS400 in a convention horizonal grow, pentration was lacking. I did do a 6 plants sort of SOG, flowered two week old clones in 4 gallon Hempy buckets. That was a better grow.
The heat sink, I think that is what it is called that DesertHydro posted,
headed in the right direction
.

Looks like that would be a good starting point.
Since I know very little about LED mechanics, and especially COB's, if I a correct the individual diodes are affixed to the heat sink. My LED lights are 5W x 80 lights, and it has is fan driven cooling.
Do you have a website with a simple tutorial on constructing an LED fixture. Would be interesting,
Just want to learn a bit about them.
GR
Click to expand...
I'll see what I can do.
 
pinner420

pinner420

Well-Known Member
sallygram said:
I have been up all damn night reading this post and figureing the changes I am going to make. Thank you
Click to expand...
So only changes are ionic is iron deficient. now days and I currently run mills for veg and ces for Bloom. I have some Jack herar 1480728714648907988297.jpg x NL brewing in veg and a nice side by side of ebb N flow vs rdwc.. same strain same birthday.
 
OneHitDone

OneHitDone

Well-Known Member
pinner420 said:
I'm just at the 24 hour brew mark... they say you can... I've never tried it.
A. load up brew ball and run for 2 weeks in system.
B. 1 gallon tea to 50 of water.

I have my reservations on A. and believe B. is feasible.
Click to expand...
And what benefit is it said to bring?
 
pinner420

pinner420

Well-Known Member
Well once bitten twice shy with anything og in my soup. I've been pouring it in over the top at full concentrate. can't really say I'm seeing any results positive or negative at this point.. still paranoid about it. think I'll run it in a separate system instead of half assing it.
 
You must log in or register to reply here.
Top