Introducing CobKits.com - specializing in DIY and Citizen COBs
ibitegirls
Well-Known Member
Yes.
nevergoodenuf
Well-Known Member
Try hanging a wet towel by the heater with a fan blowing on it. This should raise the humidity some.
Seems to be helping.
What about putting a submersible water heater in the vornado? So It's evaporating warm water instead of cold? Think this would help too?
Last edited:
SPARC
Member
Big thanks to @CobKits for his awesome service! I placed an order for some 1818s around noon on Saturday and he got them shipped out and on the way to me within a few hours. I'm going to be putting the 1818s along with some CXM22s on several frames that I designed and cut last week. I'll upload pics once they're done but here's the render I did of the frames.
The 6 COB will be 1818s with dual 185h-48a drivers. The 3 COB will be CXM22s with a single 185h-48a.
The 6 COB will be 1818s with dual 185h-48a drivers. The 3 COB will be CXM22s with a single 185h-48a.
CobKits
Well-Known Member
yes the higher the water temp the faster it will evaporate
pop22
Well-Known Member
I gave up fighting low humidity and I've seen no detriment doing so. humidifiers, etc create zones of very high humidity, which in flower can be bad. I'd rather be uniformly dry, the plants will drink what they need.
pop22
Well-Known Member
CobKits
Well-Known Member
not really. youre making a leap that it will cause extreme humidity. with good air circulation 70% humidity is acceptable in flower
CobKits
Well-Known Member
updated inventory for assembled luminus light engines
http://cobkits.com/product-category/light-engines/luminus-light-engines/
in stock ready to ship:
120mm:
3000k 80cri BJB holders
3000k 90cri BJB holders
3500k 90cri BJB holders
3500k 90cri Ideal holders
133mm: http://cobkits.com/product/cxm22-passive-light-engine-133mm/
3000k 90cri Ideal holders
3500k 80cri Ideal holders
3500k 90cri Ideal holders
all other combos of 3000k/3500k in 80/90cri (and 4000k 80 cri) are avaialble for special order allow one week for shipping
http://cobkits.com/product-category/light-engines/luminus-light-engines/
in stock ready to ship:
120mm:
3000k 80cri BJB holders
3000k 90cri BJB holders
3500k 90cri BJB holders
3500k 90cri Ideal holders
133mm: http://cobkits.com/product/cxm22-passive-light-engine-133mm/
3000k 90cri Ideal holders
3500k 80cri Ideal holders
3500k 90cri Ideal holders
all other combos of 3000k/3500k in 80/90cri (and 4000k 80 cri) are avaialble for special order allow one week for shipping
pop22
Well-Known Member
too vague. Are you talking a pre-built retail light, or a diy? If retail, most, ( non - Chinese... ) retailers will tell you who's chips they use. There's not one Chinese made cob light I'd even look at, not to say buy....
DIY? Buy quality parts and don't even worry. Whens the last time you've seen a post about someone getting bad Cree, Citizen, or Brideglux chips. I bet the Luminous chips are reliable too, or cobkits wouldn't sell them. Buy quality parts and you'll have a light equal to any high-end commercial light.
DIY? Buy quality parts and don't even worry. Whens the last time you've seen a post about someone getting bad Cree, Citizen, or Brideglux chips. I bet the Luminous chips are reliable too, or cobkits wouldn't sell them. Buy quality parts and you'll have a light equal to any high-end commercial light.
CobKits
Well-Known Member
theyre pretty predictable if you design to the specs on the datasheet
CobKits
Well-Known Member
yes.
perfect, i am going to buy an MW driver here in Arg. ,model : hlg-240-h-c700a( i cant get any driver of more mA) , was thinking of 6x luminus cxm22 3500k 90cri, or 6x citizen 048-1818 90cri , plus the 6x Ideal holders and the 6x thermal pads, all with active cooling.
Do you think this could be a good choice?
Cya!
Similar threads
