Bulk Mono Tek Pictorial
- Thread starter choempi
- Start date
choempi
Well-Known Member
I never make or use prints, clone lc
choempi
Well-Known Member
justparanoid
Well-Known Member
Nadda just waiting on my PC to be delivered so i can get busy! dang weather has it delayed.
I ordered another syringe for golden teachers and will make a LC this time before i do anything else.
JP
I ordered another syringe for golden teachers and will make a LC this time before i do anything else.
JP
choempi
Well-Known Member
gotcha, waiting is hard
choempi
Well-Known Member
Never used sporeworks but think it is a good source, they have PE which 101 does not.
They are a shroomery sponser (sporeworks), shroom talk (101)
night and day, I put links in the thread
choempi
Well-Known Member
This is a money quote...Really. Mushroom cultivation to me is one of the easiest things in the world. They are self-sustaining and rather quick. Much more so then marijuana and people on this site should be very familiar with that.
Much easier, cheaper, faster...
cazador
Active Member
Would it be better to put the tyvek on top of lid under ring?
Then put micro-tape over hole after injecting MS solution?
Or is the tyvec siliconed to the hole only under lid?
I have been on hold for to long while you all rock on. I was waiting because I wanted to use this laminar flow hood I got for a fantastic deal
I am waiting for the correct filter to arrive but while I do I am itching to start something going. It seems that you got some other people interested too. I hate feeling like a noob. It’s been awhile. I guess that’s part of the draw too. Until I get all the lingo down I might need a bit of handholding, hope that’s ok? Also while I have been waiting I have been reading, I think I’m a bit overloaded with different teks, ideas, variations of this and that… without yet putting things to practice. My plan, as advised here, is to make a MSLC first, test it to see if it is clean, then go to town with it, and to following this bulk mono tek.
Then put micro-tape over hole after injecting MS solution?
Or is the tyvec siliconed to the hole only under lid?
I have been on hold for to long while you all rock on. I was waiting because I wanted to use this laminar flow hood I got for a fantastic deal
I am waiting for the correct filter to arrive but while I do I am itching to start something going. It seems that you got some other people interested too. I hate feeling like a noob. It’s been awhile. I guess that’s part of the draw too. Until I get all the lingo down I might need a bit of handholding, hope that’s ok? Also while I have been waiting I have been reading, I think I’m a bit overloaded with different teks, ideas, variations of this and that… without yet putting things to practice. My plan, as advised here, is to make a MSLC first, test it to see if it is clean, then go to town with it, and to following this bulk mono tek. heres a shot of my homemade lid. tyvek and rtv silicone
and hers a pic of the LC jar
JP
justparanoid
Well-Known Member
This was just something i made on the fly. Now that i think about it, the tyvek should be on the outside so it stays dry.
Anyone happen to have a lid tek i can follow?
JP
Anyone happen to have a lid tek i can follow?
JP
choempi
Well-Known Member
Use 2 holes like you have and just use some micropore tape over the non silicon hole.
justparanoid
Well-Known Member
Ok sounds great. I have a roll of the micro pore tape in my closet.
JP
JP
justparanoid
Well-Known Member
Yay for you!
JP
JP
cazador
Active Member
Great!, that is what I was thinking, just didn't know if it was enough. Thanks again.
Do you have a LC solution formula that you could recomend? I see many out there. I have honey, sugar,maple syrup and light Karo in the house. If it's best to use a malt? or something i'll go to the brew store or wherever I need to go to get the correct stuff.
I'll start my own journel and stop asking personal question here. Hopfuly I'll get a mentor subbed to guide me a bit (keep me on track). I tend to want to do it all at once. small steps i know is best..