Intake vent with light trap
- Thread starter fdd2blk
- Start date
Red Eye Jim
Active Member
I was told that you can purchase a light filter from a darkroom photography supply store that lets air through but blocks light. Is this what you were looking for?
yes, this is what i'm looking for. i'll google that. thank you.
this is interesting.........
(this is for darkrooms but it's basically the same)
Terry XXXXXXX , Sep 01, 2000; 08:20 a.m.
The easy answer is to buy a darkroom fan and darkroom vents. These are manufactured devices that are light proof and have a fan or not.
<p>
I would be careful venting into a crawl space. I would run a duct from the exhaust to the outside.
<p>
For 880 cf, you want a fan of between 88 and 220 cfm. That will give you between 6 and 15 air changes per hour. Remember to take into account that ducting will reduce the air flow of the fan due to backpressure (technically static pressure losses).
<p>
The best setup for a darkroom is a combination of positive and negative pressure ventilation. You blow filtered air into the darkroom and you power exhaust air at the same time. You size the fans such that you blow in slightly more air than the draw out. This way any leaks leak air out of the darkroom, rather than in carrying dust.
<p>
THe best place to exhaust is over the sink. This way the chemical vapors and dusts are removed closest to the source. The absolute best way is via a slot hood. This is an opening about 1-2 inches high the width of the sink. This is the exhaust port. You then size the exhaust fan to suck about 200-400 cfm throught the slot. Antyhing from the sink rises slightly and then back and out the exhaust. I built this for my sink and it works great.
<p>
BTW my background includes industrial ventilation design for contaminant control. So I am giving you advice to make a GREAT setup. The other posts will work, maybe not as well, but they will work. The big thing is to exhaust near the source and get enough airflow.
(this is for darkrooms but it's basically the same)
Terry XXXXXXX , Sep 01, 2000; 08:20 a.m.
The easy answer is to buy a darkroom fan and darkroom vents. These are manufactured devices that are light proof and have a fan or not.
<p>
I would be careful venting into a crawl space. I would run a duct from the exhaust to the outside.
<p>
For 880 cf, you want a fan of between 88 and 220 cfm. That will give you between 6 and 15 air changes per hour. Remember to take into account that ducting will reduce the air flow of the fan due to backpressure (technically static pressure losses).
<p>
The best setup for a darkroom is a combination of positive and negative pressure ventilation. You blow filtered air into the darkroom and you power exhaust air at the same time. You size the fans such that you blow in slightly more air than the draw out. This way any leaks leak air out of the darkroom, rather than in carrying dust.
<p>
THe best place to exhaust is over the sink. This way the chemical vapors and dusts are removed closest to the source. The absolute best way is via a slot hood. This is an opening about 1-2 inches high the width of the sink. This is the exhaust port. You then size the exhaust fan to suck about 200-400 cfm throught the slot. Antyhing from the sink rises slightly and then back and out the exhaust. I built this for my sink and it works great.
<p>
BTW my background includes industrial ventilation design for contaminant control. So I am giving you advice to make a GREAT setup. The other posts will work, maybe not as well, but they will work. The big thing is to exhaust near the source and get enough airflow.
now that you mention it, i need to cover my exhaust as well.
W33D
Well-Known Member
Hook some black tubing up long enough so light doesn't show through. Have it sealed on the inside part of the intake vent, and run the tubing along the bottom of the room, giving it "corners" if necessary to block light and allowing fresh air underneath the canopy. This is one method that came up in a brainstorm. Another was making block sort of thing like steps inside so light doesnt bounce off the "/\/\/\" and get through the other side. Get it?
i think i may go with this. my buddy builds swimming pools and has a garage full of fittings and pipe. i could make it look like the stack on a semi.
Picasso345
Well-Known Member
I've battled this too. For my passive intakes I've used the $25.00 Doran 8"x8" light proof vents. - look at B&H Photo: Darkroom Fans & Louvers | B&H Photo Video Work great.
Great deal here:Doran Dark Room No-light Fan and 2 no-light vents - eBay (item 290229610744 end time May-13-08 11:25:37 PDT)
A more ghetto solution is black pantyhose. I used it on my passive intake for the hood vent. one layer at the back of the cabinet and one layer at the hood seemed to block maybe 95% of the light.
Great deal here:Doran Dark Room No-light Fan and 2 no-light vents - eBay (item 290229610744 end time May-13-08 11:25:37 PDT)
A more ghetto solution is black pantyhose. I used it on my passive intake for the hood vent. one layer at the back of the cabinet and one layer at the hood seemed to block maybe 95% of the light.
t0k3s
Well-Known Member
you could you put a carbon filter on the intake and out take.They are light proof and it will keep the air coming in clean and the air going out clean
Thats how i keep my light in to prevent stunting growth in flower.HTG has some 60$ ones that work good or you could build your own
Ryoko Builds a DIY Activated Carbon Filter - 30 Minutes, $30 Dollars - The Garden's Cure
Thats how i keep my light in to prevent stunting growth in flower.HTG has some 60$ ones that work good or you could build your ownRyoko Builds a DIY Activated Carbon Filter - 30 Minutes, $30 Dollars - The Garden's Cure
got it. thank you everyone for all the ideas. i put them all together.
i went with black PVC 4". i used a couple elbows to diminish light. i then stretched black pantyhose over the end and capped it with a cute little cap..........
for the exhaust i used the box my new fan came in. i flipped it over the top of the hole and secured and sealed it with tape and staples. then i cut a door in the side. i covered that with pantyhose and made the door adjustable........
it all works great.
i went with black PVC 4". i used a couple elbows to diminish light. i then stretched black pantyhose over the end and capped it with a cute little cap..........
for the exhaust i used the box my new fan came in. i flipped it over the top of the hole and secured and sealed it with tape and staples. then i cut a door in the side. i covered that with pantyhose and made the door adjustable........
it all works great.