New Experimental Advanced DIY Designs.

[stardustsailor]

Until ,savings will allow for something better ....
One has to keep experimenting (and growing ) with what he has ....

So ..Next project ...

""Summerlight " ....

6 panels ...

( 150 Watt total at plug-drivers included. ~25 Watts per panel . )

Each panel .... :

16 x WW ( 2500-2700 K )
4 x red 620-640 nm
2 x NW ( 4500-5500 K )
1 x red 650-660 nm
1 x violet 395-410 nm



Spectrum (approx) :

The panels :

 

[PetFlora]

[h=1]Sacred Geometry 101D: Concentric Circles
[/h]http://www.youtube.com/watch?feature=endscreen&v=D39eGrx3a_A&NR=1

Advance to roughly 2:30 Seed of Life, Tree of Life and Flower of Life, which is THE key, and then there's Metratron's Cube

 

[stardustsailor]

...

Designing Astir's 'flagship'.....


Some details :
-Full aluminium construction .
-96 x Osram SSL oslon 80 . (350-550 mA )
-All electronics fuse protected (x2 )
-Special relay circuit .If fan(s) fails ,leds switch off.
-MeanWell drivers (x4 )
-Emb papst 120 mm Fans (x2 )
.....

 

[PetFlora]

How about angling the switches to 45*s for easier access. Also looks like the power cords will be in the way if kept where you have them

 

[stardustsailor]

How about angling the switches to 45*s for easier access. Also looks like the power cords will be in the way if kept where you have them

45 degrees ...? ..
Nope ....Too complicated design (in manufacturing..=>higher cost -....already way high ....-

No cords there ...Neither drivers ....
Early blueprints ...
Only basic design ,fans,fuses and switches ...
Cord will be on top ...(cord for mains ) ....

Anyway....Thanx 4 the remarks ....

 

[stardustsailor]

Spectrum ....

4 led pcbs ...

(50 x 60 mm )

Each having 24 pcs of leds ....

16 x Warm Whites 2700 K of the LCW CQ7P family ....
4 x Neutral Whites 5000 K ,also,of the LCW CQ7P family ....
4 x LH CP7P 645-660 nm hyper reds ...

On each heatsink ,2 x 24 led pcbs .....



(Exact led types,will remain a small " trade " secret ...)

 

[ganja 2]

maybe the 4 switches should be placed at the side and not at the top cause they will be diffycult aproaced when the panels will be hanged at 2 metres high for example...

 

[ganja 2]

great job by the way bro..!

 

[stardustsailor]

Oh it has plenty of work still ....
But ...it's moving on ...

 

[PetFlora]

45 degrees ...? ..
Nope ....Too complicated design (in manufacturing..=>higher cost -....already way high ....-

No cords there ...Neither drivers ....
Early blueprints ...
Only basic design ,fans,fuses and switches ...
Cord will be on top ...(cord for mains ) ....

Anyway....Thanx 4 the remarks ....

You are missing it. It is not complicated. SIMPLY turn the switches 45*, otherwise, one switch is directly behind the other and hard to reach over

 

[stardustsailor]

Ok ...That's much better ...

 

[stardustsailor]

Ok....
Let's see ....

It' looks niceeeeeeee ....

 

[ganja 2]

maybe the drivers heated ?

 

[PetFlora]

I would like to see the diodes configured in Merkaba clusters, with 1 NW in the center, surrounded by WW- OK, maybe you don't this BUT...

If the NW was a 3w diode and the NW one watt diodes, the NW could be on its' own dimmable circuit. More during veg, less during flower

 

[stardustsailor]

I would like to see the diodes configured in Merkaba clusters, with 1 NW in the center, surrounded by WW- OK, maybe you don't this BUT...

If the NW was a 3w diode and the NW one watt diodes, the NW could be on its' own dimmable circuit. More during veg, less during flower

No need for that ..
This light's spectrum covers everything ....

 

[stardustsailor]

....



As long as fan operates ,relay stays closed and mains power pass through relay,to fuse to led drivers ...
(relay has to be cooled ..attached to alum surface ... )

If fan stops working ( fails ) ,relay 12 V circuit opens ,so does the mains circuit to led drivers ..
Power is cut-off ...
Leds are switched off ..
New fan has to be installed for the leds to switch on again ....
(or by ' overriding ' the " Fan-Fail-Safe" circuitry ....with a single ' bridge ' )

 

[stardustsailor]

maybe the drivers heated ?

Still early design ...A lot should change ...

 

[stardustsailor]

maybe the drivers heated ?

One option is this ...

...




.....\

Build .....Like a tank...../

 

[tolakra]

It could have a hole (with screen-σίτ&#945 above the drivers-between the fans, so that the heated air around the drivers isn't trapped in there.
The fans are blowing air in the panel right? The air will get away through the sides of the panel as well as trough the center of the panel.
If there isn't a hole in there, the center of the panel will not be cooled right

 

[stardustsailor]

It could have a hole (with screen-σίτ&#945 above the drivers-between the fans, so that the heated air around the drivers isn't trapped in there.
The fans are blowing air in the panel right? The air will get away through the sides of the panel as well as trough the center of the panel.
If there isn't a hole in there, the center of the panel will not be cooled right

Yeap.....