so im in the middle of harvesting and turned the lights off for 48 hours. i read online of a better way to dry and trim, basically you let the plants die in its place so the leaves just naturally fall off. half my harvest is chopped up and i wanna try that method with the other 2. problem is...
so im 2 days away from cutting down the trees and heard somewhere that cutting the fan leaves 2 days before harvest helps with resin production along with turning off the lights for the last 2 days. i was wondering if anyone has done this and how it helped. ive heard of the turning the lights...
Ok so today i go into my grow room after 2 days of not really checking and as im feeding my plants i notice on the other side of the room mold!!! it was in the corner and spread half way down the wall but didnt go up the wall. I cleaned it immediately with lysol, scrubbed, and dried. Its all...
So im not sure if this yellowing is due to heat because i caught my plants right under the hood i have (air-cooled) or if its due to zinc. I dont want to treat for zinc if its the heat and is this stuff still fine or take the loss?
all my nutes are advanced nutrients
connoisseur
bud igniter...
so i had to cut down my plant early :( and need to dry it out quick. usually i would hang them upside down but was wondering if theres another way? is it ok if i leave them all together in a box overnight? or will this make them moldy?
so heres my plants at week 6. i was using the house and garden feeding schedule and realized that the budding didn't happen till week 5 of the schedule -_- plus they have been through some stress. basically no running water for 2 weeks -____- but they didn't die and nothing bad happened since...
ok so i changed the water 2 weeks ago, when i went to change the water last week the pump wasn't on, thankfully the plants were able to get the nutes cause its roots are so long (NFT system) then today i go to check on them knowing the pump is on and see that the actually tube of the water pump...
hey, so my plants are too big and fall over when i take them out of the tent to change out the nutes. i was wondering if it was ok to drain as much water as possible from the res then getting one of those plastic totes from target and use a pump to put it in the plants res. i know this is an...
ok so the plants reached about 3 ft and i just gave it some bud nutes. when i went to change the res i had to take the top part out and the 2 big ones kinda started leaning over to the side. now this is like the 3rd time it happens but i was wondering if there are any suggestions to kinda change...
the light is more moved to the center since i don't even have my filter in yet and bumped back unto 600w now since the plant is so close will it stop growing or get burnt?
here are some pics of the babies so far.
sorry for the shitty quality, the light tosses my camera off. also should i try getting some lights for the bottom or something? they literally are so bushy i doubt the lower leafs could get light even with some trimming.
right on, ill post more pics later on. but should i back off the nutes a bit for the yellow tips? or lower my water pump? usually when i feed i get in between aggressive and normal for the base nutes of aqua flakes. btw i messaged you, ignore it but should i be worried that no bud is on the...
hey ok so i got some cal mag and added that into the mix for the week, they look better and are legit like 5 inches away from the light, they are growing quick i got a ppm meter and my ph meter should be fine but i might get a 2nd one to just make sure its all good. now the plants leafs at the...
hey so i read somewhere here that fem seeds are bad cause they are chemically altered idk if it really effects the potency or something but id like to get some opinions and would like to know how or if i should make colidle silver? and get a branch to get seeds from the plant to have another...
bear:
I have a bluepen for ph i know the other day (dumb as it was but i was high) i sunk it in the water cause the ph was varying so my thought was "well the bottom would be best for ph accuracy" thats when the ph really started fluctuating but i calibrated it so it should be fine but idk if...