Search results

Yeah this is my first grow as well. I jumped right into DWC Hydro which has been a real learning experience. Lots of fun.

The camera is a Carson zOrb USB Digital Microscope with 53x Optical Zoom, Surf Blue (MM-480B). You can pick it up for about $40 from Amazon. You will need a laptop or desktop computer to plug it into to take pics. As with all microscopes you will have to use something to stabilize it while...

Thanks to all for their comments & advise. This is an exciting time.

I am just now into the sixth week since the flip. I struggled some with PH flux and nute issue early on (newbie mistakes), but new growth seems to be better now. I'm sure the issues I have experienced will affect overall yield, but I'm just trying to get to the end of my first grow. Strain is...

Folks, I need some advise as to how close I am to chop. I have attached the best pics I could get of my trichs and pistils. This is my first grow and the time of truth must be nigh. I hope! Thanks

Wow, makes good sense now. Is it OK to add a little clearex to the RO PH'ED water change for the rez?

So I use RO water and add 2.5ml/gal of CaliMag at each rez change which is every 7 days. Ph has been steady at 5.8-5.9 for weeks but it sounds like you think it may be locked out? Or I may have to up the CaliMag? Are you saying if it does not uptake water immediately it was locked up?

Folks, trying to figure out what is going on with my kids that are in their 5th week of flowering. I'm growing indoors in a DWC setup and I'm suspecting nute burn but I needed some expert advise as this just seemed to appear in 24 hrs. Only one flower has the severe condition, others are more...

Would you just tie/wire them to the bottom of the net pot?

Sorry, so just to be clear, the tangle is between two different plants side by side. Still common?

I have a grow in its 4th wk of flowering in a DWC setup with 4 plants and a couple of them have roots really tangled. They have made a big cluster that is near the surface of the solution, but always covered with solution. Roots and plants are healthy, so I'm just wondering if there are any...

Thanks for the advise Atomizer! I'll see if any of these things help. I've also learned that you can wrap the Ballast cord going to the light shield with conductive tape (aluminum or copper) and that sometimes helps. I also read about using Ferrite Wire Clips that snap around the power cable. I...

Nice reference document. Better than what Hanna sends with their meter. Yes I'm using the H17031 (1431us) calibration packets for my H98129 meter. The conversation is set to .50 and the Beta setting is 2.1. I'm not sure what the Beta setting is for, or what it affects?

OK so get this. I just realized that my 400W Yield Lab light ballast is causing RFI to my CWP 24/7 Nutrient Monitor. The ballast has a variable 25-100% setting and when it is set at the 100% setting it increases the PPM reading by about 250 PPM. When I lower the intensity setting, the PPMs...

Wow, great advice. Very thorough process.

Nute strength has been lowered to around 800 PPM on my CWP Monitor. Please explain comment on "I hope you aren't confusing your meter readings with PPM". Thanks

Keep thinking A~~~! I actually have two meters, a continuous reading PPM/PH/Sol Temp unit from CWP Instruments and a Hanna H198129 PPM/PH hand held meter and they both are very close in PPM readings, recently Cal'ed. And I am going to lower my PPM to 800 now. Thanks Tman

No, I am still using the GH Flora Micro and Bloom liquid (no Grow), but I'm mixing at a Micro=7ml/gal and Bloom=14ml/gal instead of Lucas recommended 8/16 ratio. I'm running with you guys advise to lower my PPM. I just diluted down to 1100 PPM from 1300, it sounds like I need to go more?

Thanks Future, that all makes good sense. What do you recommend for pest treatment. I just ordered some Hot Shot vapor strips from amazon. Have you ever used any of these? http://www.hotshot.com/Products-and-Solutions/All-Products/No-Pest-Strip.aspx