Aero/NFT Grow in Tent w/ CO2, AC, Dehumidifier, and DIY Chiller

AKGrowAreo

Well-Known Member
I have a low pressure aero/nft grow going in a 4x8 tent and I have been getting some great results. I am about to ditch the tent for a larger space, but wanted to post about my success in the tent because contrary to popular belief, co2 can be successfully run in a tent, even on a budget.

This is my take on the @StinkBud method so big ups to him for all he brings to the table.

Anyway please give me your thoughts on my grow and let me know if you have any questions.

FullSizeRender.jpg IMG_2879.JPG IMG_2885.JPG IMG_2891.JPG IMG_2893.JPG IMG_2896.JPG IMG_2911.JPG IMG_2962.JPG IMG_2966.JPG
 
Last edited:

AKGrowAreo

Well-Known Member
These are a couple of the seedlings. I actually just harvested 6 of these and got over 39oz so I am stoked!

IMG_3087.JPG
IMG_3108.JPG
This Trinity plant is my favorite pheno from the Trinity seeds I bought.
IMG_3114.JPG
This right after I topped these bitches
IMG_3115.JPG
Check out all the clones! 100% rooted...too bad I threw away a bunch cause I couldn't find anyone that needed clones...
IMG_3122.JPG
Supercropping time!
IMG_3131.JPG
The night these ladies moved into flower...
IMG_3165.JPG
There they are on the right side of the flower tent
IMG_3188.JPG
 

AKGrowAreo

Well-Known Member
Ok moving on...
I have access to a fresh cold water faucet in my grow area and a drain. If you have these in your area try this out. It works absolutely great.
This was my #1 concern, keeping my reservoirs cool. I researched, then researched, then researched some more.

The idea of a traditional chiller was too expensive and pretty inefficient, and pumping my nute solution to a remote chiller seems fucking retarded (how to keep the lines from getting dirty, potential for flooding, extra reservoirs, fuck that business). Peltier Thermoelectric chillers simply would not do good enough, they are expensive to buy, annoying to make, and quick to fail. So what were my other options? I was stumped!

I went back to the drawing board and designed my own reservoir chilling system. Full disclosure, I am positive that other growers have developed the same chilling system as I did, but I could not find shit about it on the web so I designed this one all on my own. I am not claiming to have invented style of chiller, but I am fucking stoked on it and would love to hear from anyone who has done anything similar. My first designs were very similar to other DIY chillers out there and there was nothing special about it really. My first plan was to put put a coil of hose in a fridge and pump my nute solution through it using a timer. It would have worked, but also would have used unnecessary electricity and added extra headaches.

Frustrated, I then remembered that I had used a little thingy called a wort chiller when brewing beer in the past. Basically this is a immersion chiller that consists of a coil of metal tubing (usually copper, but you want a stainless steel one to prevent any leaching from the copper caused by the nute solution). What a great way to go! This meant I wouldn't have to keep any extra pumps in my res and I never have to move the nute solution out of the res to chill it! Duh, tons of people are using these so I don't know how I missed it!

I set out to put a really big res filled with potable RV/marine antifreeze into a freezer, then put a pump in the res connected to a hose that pumps the antifreeze through the wort chillers that sit in my reservoirs. The pump would be turned on and off by the another one of these $38 Inkbird thermostats with sensor and outlets built in.

Right when I was about to buy a fridge I had little light bulb go off in my head! Why the fuck should I wast time, power, and money on a fridge when my tap water is 43 degrees once it runs for a minute or two? I was stoked! I had finally figured it out!!! I am lucky enough to have a drain in the floor of my grow area and I plumbed cold water faucet to the area as well. Without both of these, you will not be able to run this chiller, sorry.

I turned my attention from fridges to sprinkler valve electronic relays. They are cheap and they last forever! Here is how it ended up working out. Don't buy cheap hose parts though because THEY WILL LEAK! I was able to build my chiller for my 2 flower room reservoirs for about $210 and its really easy to build. Shit is extra expensive where I live, so you can probably do better. I will do a detailed thread with pics and instructions on how to build this chiller as soon as I have some down time, but here are the basics.

These items work for my set up. You may need slightly different lengths of tubing, hose and more or less of some items. Measure and plan before you buy!

Supplies For 2 Reservoirs:

1 cold water hose faucet (sink will work but you'll need a garden hose adapter)
1 drain
2 - Super Efficient 3/8" x 25' Stainless Steel Wort Chiller = $40 each (brew shop or Amazon)
1 - Inkbird Itc-308 Digital Temperature Controller Outlet Thermostat, 2-stage = $38 (Amazon
1 - Orbit 57100 3/4-Inch Female Pipe Threaded Auto Inline Sprinkler Valve = $12 (Amazon)
1 - Orbit Sprinkler System Power Source Transformer 57040 = $13 (Amazon)
1 - box of miscellaneous wire connectors = $5
2 - male 3/4 threaded to male garden hose adapters = $5 each (Lowe’s)
2 - 2 Way Solid Y Valve Garden Hose Connector Splitter Adapter = $13 each (Lowe’s)
1 - PTFE Pipe Thread Seal Tape = $2 (Lowe’s)
1 - 50’ length of garden hose = $13 (Lowe’s)
6 male and 6 female (this should be enough to have extras) hose repair pieces = $5 each (Lowe’s)
1 - 20’ length of 3/8” vinyl tubing = $10 (Lowe’s)
1 - 3/8” vinyl tubing T = $3 (Lowe’s)

Instructions For One Reservoir: (If only chilling one res you will only need 1 wort chiller and you wont need the vinyl tubing T.)
  1. Connect 2 Way Y Valve Garden Hose Adapter to water faucet.
  2. Connect one side to the new garden hose and the other side to your old garden hose (if you have one).
  3. Run the hose close to your flower room and cut it to an appropriate length (pvc pipe cutters work great for this).
  4. Connect female hose repair piece to the end of the hose where you just cut it.
  5. Connect the 2 male 3/4 threaded to male garden hose adapters to the Orbit 57100 3/4-Inch Female Pipe Threaded Auto Inline Sprinkler Valve using PTFE Pipe Thread Seal Tape and be sure to tighten well using crescent wrench.
  6. Connect the hose to the Orbit 57100 and tighten well. Be sure to find the arrow to ensure the water goes in the correct hole and out her other.
  7. Connect Orbit Sprinkler System Power Source Transformer 57040 to Orbit 57100 using wire crimpers and connectors.
  8. Connect another female hose repair piece to the other cut off end of the hose.
  9. Connect the hose to the out end of the Orbit 57100 and tighten well.
  10. Clean the wort chiller using dish soap to remove any machining oils and rinse well.
  11. Insert wort chiller into reservoir.
  12. Connect wort chiller to the garden hose.
  13. Connect vinyl tubing to other end of the wort chiller.
  14. Run vinyl tubing to drain.
  15. Connect Power Source Transformer to the cooling outlet on the Inkbird Itc-308 Digital Temperature Controller Outlet Thermostat.
  16. Put temp sensor in the reservoir.
  17. Plug thermostat into outlet and set desired temp, dead band, alarms, etc. Calibrate the unit if necessary.
Instructions For Two Reservoirs:
  1. Follow instructions 1 through 9 from above then the following
  2. Run the garden hose to a central location between the two res and cut.
  3. Connect male hose repair piece to the newly cut end.
  4. Clean the wort chillers using dish soap to remove any machining oils and rinse well.
  5. Insert wort chillers into reservoirs.
  6. Connect vinyl tubing to the supplied garden hose adapter.
  7. Run tubing to the wort chiller and cut to appropriate length.
  8. Repeat steps 6 and 7 to the other wort chiller.
  9. Connect vinyl tubing to both wort chillers using supplied clamps.
  10. Connect separate vinyl tubing pieces to the other end of each wort chiller.
  11. Run the end of the tubing to a point where you can connect them to the vinyl tubing T.
  12. Connect another piece of tubing to the other end of the T and run the tubing to the drain.
I set my res temp to 67 degrees with a 1 degree dead band so that the second the res it gets above 68 degrees the sprinkler relay is activated and cold water starts flowing through my wort chillers and thus chilling my nute solution. As soon as the temp goes below 67 degrees the water ceases to flow. I keep my sensor in my warmer of the two reservoirs and they stay within 1 degree of each other. I could adjust the flow to each res using the valves on the y adapter to get the temps exactly the same if I wanted, but I just keep the valves wide open cause I am not worried about the 1 degree difference. Make sure to secure the vinyl tubing into the drain in some way. If you don't the line has a tendency to pop out of the drain and start spraying water everywhere.

Inkbird Thermostat

Orbit 57100 3/4-Inch Female Pipe Threaded Auto Inline Sprinkler Valve (sprinkler relay)

I have it housed in a bucket just so its out of the way and doesn't get kicked accidentally.

I don't have any pics of the wort chillers, but they are pretty straight forward. Let me know what you think about this and would love to hear about other's experience with similar set ups.
IMG_3253.JPG IMG_3254.JPG IMG_3255.JPG IMG_3256.JPG IMG_3257.JPG IMG_3258.JPG IMG_3259.JPG IMG_3260.JPG IMG_3262.JPG
 
Last edited:

AKGrowAreo

Well-Known Member
This is about 4 weeks into flower
IMG_3436.JPG
Trin was looking real nice at 4 weeks
IMG_3437.JPG
more trin
IMG_3438.JPG
Sadly I lost this girl scout cookie to herm :sad::sad:
IMG_3439.JPG IMG_3441.JPG
Crazy how indica roots are so much more aggressive than the sativas...at least from my experience.
IMG_3443.JPG
Trin
IMG_3444.JPG
Mystery afgan plant that a friend gave me, it turned out just ok
IMG_3465.JPG
 

AKGrowAreo

Well-Known Member
The night before harvest
IMG_3632.JPG
night before harvest
IMG_3633.JPG
trinity looking fucking dank! Tastes amazing too!
IMG_3637.JPG
Same nug as above with his best friend all trimmed up. I kept these for my personal!IMG_3650.JPG
Trimmed and dried Blackberry OG nug. Best pot I have ever smelled or tasted, its fucking nuts...tastes just like the berry and smells just like it too!
IMG_3656.JPG
close up of the blackberry og
IMG_3666.JPG
 

Attachments

letdown shifty

Well-Known Member
We've gotta get you one of my chillers going for your new set up bro. Its so easy and so nice to know your res is always chillin' (no pun intended)
Haven't really needed a chiller as of yet. I run my reservoirs outside of the tent currently, so they are out of the light. Cut 2" holes in tent that the rails drain thru 2" pvc back into res
 

AKGrowAreo

Well-Known Member
Haven't really needed a chiller as of yet. I run my reservoirs outside of the tent currently, so they are out of the light. Cut 2" holes in tent that the rails drain thru 2" pvc back into res
Thats awesome. I've played around with the idea of keeping my res outside of the room, but I haven't pulled the trigger on it cause my nutes stay at 65 degrees with the chiller even though I run my tent at 85 degrees ( have to run hot to get the co2 to do its job). If you end up going with co2, and having your res' in side your new grow room you will definitely need a chiller. I have also played around with the idea of burying my res' in the floor.
 

letdown shifty

Well-Known Member
I think I'll still keep my reservoirs outside of new room, can check them without disturbing flowering. I will just have to increase my pump sizes to adjust for longer piping. 1 other variation I made from @StinkBud system is I don't have sprayers in my flower rails. The res just pumps into end of rails and streams down. I was having issues with roots clogging sprayers
 

AKGrowAreo

Well-Known Member
I think I'll still keep my reservoirs outside of new room, can check them without disturbing flowering. I will just have to increase my pump sizes to adjust for longer piping. 1 other variation I made from @StinkBud system is I don't have sprayers in my flower rails. The res just pumps into end of rails and streams down. I was having issues with roots clogging sprayers
Cool so you are running a true NFT. Thats awesome!
 
Top