HoppusTheCaveman
Well-Known Member
I've been asked multiple times to post how to do this, and I finally went and did it. Only thing is that it's just Paint pictures, and they're a little crappy. It gets the point across pretty much though. I'll probably end up making a better one with real pictures sooner or later. So here it goes.
If you're really serious about making this piece of art, please do take your time in making it. You need plenty of patience to make this look/work well. So again, I advise you to go slow with this, especially if you are a novice roller.
1) You're going to need 3 things for this creation. #1 being weed of course!! #2 would be rolling papers. Whatever you prefer of course. Now the #3 thing is anything remotely pointy to make the hole in the larger joint so you can stick the smaller one in.
2)Take two papers, and roll up two joints. One SIGNIFICANTLY thinner than the other. If they're about the same size, then you won't get them to cross succesfully, therefore making a bad cross joint. You don't want that do ya? No, no you don't.
3)Now with your mystery object, you are going to make a hole in the fat joint going all the way through about the same size as the thinner joint. Maybe even a little bigger so it fits through better, but not TOO much bigger. If you aren't careful, you'll end up with the top end falling off....which is not good at all. Now with the thinner joint, cut/tear the middle of it VERY GENTLY so as not to rip it completely in half. You also want to make this slit very small as well so it doesn't rip in half when you put it through the other joint.
4)Now that you have the hole in the fat joint, stick the thinner joint in it and gently(so as not to rip it in half) push/pull it through until the joint is sticking out about evenly on both sides. When you have that done wi- DON'T light it up just yet!! There's still one more thing you have to do. Take another paper, and cut off the sticky part with scissors. Wet it and then wrap it around where the joints intersect to make it secure, and so it's airtight.
5)Now that you have an absolutely bodacious cross joint, go get some absolutely bodacious friends to help you light it up and help smoke it all. Enjoy!!
If you're really serious about making this piece of art, please do take your time in making it. You need plenty of patience to make this look/work well. So again, I advise you to go slow with this, especially if you are a novice roller.
1) You're going to need 3 things for this creation. #1 being weed of course!! #2 would be rolling papers. Whatever you prefer of course. Now the #3 thing is anything remotely pointy to make the hole in the larger joint so you can stick the smaller one in.
2)Take two papers, and roll up two joints. One SIGNIFICANTLY thinner than the other. If they're about the same size, then you won't get them to cross succesfully, therefore making a bad cross joint. You don't want that do ya? No, no you don't.
3)Now with your mystery object, you are going to make a hole in the fat joint going all the way through about the same size as the thinner joint. Maybe even a little bigger so it fits through better, but not TOO much bigger. If you aren't careful, you'll end up with the top end falling off....which is not good at all. Now with the thinner joint, cut/tear the middle of it VERY GENTLY so as not to rip it completely in half. You also want to make this slit very small as well so it doesn't rip in half when you put it through the other joint.
4)Now that you have the hole in the fat joint, stick the thinner joint in it and gently(so as not to rip it in half) push/pull it through until the joint is sticking out about evenly on both sides. When you have that done wi- DON'T light it up just yet!! There's still one more thing you have to do. Take another paper, and cut off the sticky part with scissors. Wet it and then wrap it around where the joints intersect to make it secure, and so it's airtight.
5)Now that you have an absolutely bodacious cross joint, go get some absolutely bodacious friends to help you light it up and help smoke it all. Enjoy!!
, norm my main joint part is longer (king size) and i use 1 skin for the cross, when spaced properly it burns perfectly to the middle section then carries on down.
