Right speed controller?

RedSloth420

RedSloth420

Member
Hey guys, so I have this inline fun that I need to reduce and am wondering which type of controller would work without messing up the motor.

Any suggestions and/or advice is much appreciated.
 

Attachments

U

upnsmoke13

Well-Known Member
just got one of those, turned my inline fan down with NO noise (from the motor/transformer). fixing to order my second one!!
 
Beezcheeze

Beezcheeze

Well-Known Member
I bought 2 also. They both work great. Using this along with my 2 6" vortex fans and it's almost silent even on 100%.
 
Gr8ness

Gr8ness

Well-Known Member
Beezcheeze said:
The only one I that works and doesn't harm the motor was on Amazon.

http://www.amazon.com/gp/aw/d/B006NGI8VS/ref=mp_s_a_1_1?qid=1425242268&sr=8-1&pi=AC_SX110_SY165_QL70&keywords=variac speed controller
Click to expand...
I've got 2 different in-line fans :

1) http://www.christmas.com/ideadetails/153372/
2) http://www.amazon.com/Vortex-Inline-Fan-10in-790CFM/dp/B004TJFO5O

I was wondering if this speed controller would work on either of these fans (should the need arise for me to swap it out between fans), once at a time of course.
 
A

az2000

Well-Known Member
The variac is the quietest speed control. I have a couple of the inexpensive dimmer-like controllers. They cause a buzz in the fan, probably due to the AC voltage being clipped (like 60 on/off pulses every second). It's reported to be bad for fan motors.

I've been playing with a way to have the fan switch between an idle speed that just enough to refill the tent every 5 minutes (common rule of thumb for sizing a fan to a tent) and full speed to evacuate heat if it builds up. Also thinking about tying this setup into my light timer so it will go to a higher idle speed when lights on (using a fixed voltage transformer instead of a variable.).
 
Beezcheeze

Beezcheeze

Well-Known Member
Sounds like a good idea in theory^^ let us know how you get that to work. That's a great way to have ventallation. I can see how you'd do it with 2 seperate fans but...
 
Cannasutraorganics

Cannasutraorganics

Well-Known Member
image.jpg image.jpg Grozone. TV2. Thermal speed control of fan.
Set temp and idle speed. Idle from 20% to 60%. When temp goes above set degree it increases fan speed to control. All the way to 100% and in 5% increments if necessary. If it goes 6 degrees colder then set point it turns fan off so not to make it too cool for plants.
On start up it puts full power to start the motor then decreases to needed speed. And you can set to turn off at lights out too.
 
Last edited:
RedSloth420

RedSloth420

Member
Thank you for your suggestions guys. I pulled the trigger on the variac controller and I'll let you know how it goes once it gets here.
 
Tim Fox

Tim Fox

Well-Known Member
congrats, you made the right choice, its the most advanced kick ass controller going, wait till you hold it and feel the weight of it, its solid and it gives you FULL control over your fan, quiet days ahead for you
 
Tim Fox

Tim Fox

Well-Known Member
thanks for the heads up, but upon inspection of my amazon variac controller it seems to be built like a tank, its heavy, has great vents, the connections look solid inside ( yes i opened it up), and it controls my fan like a dream, oh and it doesnt even get hot when controlling my 6" fan all the way down to a whisper, maybe you got a bad one, even mercedes benz builds a bad car now and then, just a lemon i suppose?
 
jijiandfarmgang

jijiandfarmgang

Well-Known Member
Tim Fox said:
thanks for the heads up, but upon inspection of my amazon variac controller it seems to be built like a tank, its heavy, has great vents, the connections look solid inside ( yes i opened it up), and it controls my fan like a dream, oh and it doesnt even get hot when controlling my 6" fan all the way down to a whisper, maybe you got a bad one, even mercedes benz builds a bad car now and then, just a lemon i suppose?
Click to expand...
There's a reason why its a hell of a lot cheaper than say a US made version.

Its not UL or even CE listed. It by nature is heavy, but the body is just thin stamped steel, with a 1 cent power cord. Not what I would call heavy duty.

I'm not saying it wont work, just know what your buying.

There's a good thread on another forum where a member was severely electrocuted by his, I'll see if I can find it.

- Jiji

EDIT: Heres where Pontiac mentions it, if you search around in another thread he goes into detail about what happened.

https://www.icmag.com/ic/showthread.php?t=141509
 
Tim Fox

Tim Fox

Well-Known Member
I was kinda chuckeling to myself all night at work last night about this thread, because it came to me, that my speed controller is made in china, my $1 dollar extension cords from home depot are made in china, my mars hydro led is made in china, heck I bet even my recycled wardrobe from the renovated hotel is fiberboard from china ( uses those speed connectors and lays flat like IKEA stuff does), If I start speaking WANG CHUNG when I smoke weed I grow in my cab, I will need a good shrink! LOL
 
You must log in or register to reply here.
Top