DIY E-Nail

budbro18

Well-Known Member
First 3 should be done soon week or so at this point. nails should be in in a week possibly less. Gotta do some testing and make sure everything fits and functions how i want it to.

Ill get movin double time now that i know you really want one.
 

watdaheo808

Active Member
Thanks guys! I figured i was goin into it so i might as well help educate everyone else.

If youre following the guide make sure you get the bigger box that i posted about.

As for nail i just got the picture of the custom TI ones i had made. Basically the highly educated OG enail but slightly different with interchangeable male/female 10/14/18mm down stems



Here they are without the 10/14/18mm plugs/caps
Do you have any pictures of the interchangeable male/female adapters?
 

budbro18

Well-Known Member
No but theyre similar to ones already out there

I basically just had a guy take his design for the post coil domeless nails and make it the right diameter and height for the 16mm coils.
 

LiquidJunglist

Well-Known Member
All I'm interested in 1 with a 10mm male adapter. Looking to buy a separate coil and nail for a 10mm travel rig.

Also BudBro could you give me a idea on how much power the unit pulls? I've been wanting to build a DIY Portable Power Station for when I go camping and/or hiking. I'm going to in time do the DC Enail but want to get my feet wet with the AC. Just wanted to see how big a battery I might need to get.

If you have a Kill-a-watt or a tester you could tell how much it pulls when it heats and when the dab hits the nail.
 
Last edited:

Fadedawg

Well-Known Member
Just a mockup to try it out, but here is a jury rig we did for trials and to have a unit on hand to help Waywardwolf sort out a complete unit over the phone, that we built in SoCal and which as it turns out, has a defective Mypin controller.

It is in learning mode, so the lower number isn't the set point. That was actually 600F and the nail works slick.photo.JPG
 

duval904

Active Member
I have Digital E-Nail's for sale now that was put together very similarly to this and has been dialed in to not overshoot and maintains a perfect temp for low temp dabbing at 710 F. If you're interested pm me or check out my page. FULLY CUSTOMIZABLE with any decal and made to order so you know the most precision was put into each unit made just for you!!!

https://www.rollitup.org/t/low-temp-dabbing.828549/
 

budbro18

Well-Known Member
Well its only a 125-200w coil max. So not that much. About as much as a few old incandescent bulbs. But most of that is on start up.

Unfortunately i dont have a killawatt but i would assume it would be like an electric oven. Larger amount at the beginning then small amounts once it gets flowin.

Maybe someone who has one on here would be kind enough to hook it up to their killawatt if they have it.

I know people keep em on 24/7 almost and dont see a noticeable increase in their electric bill.
 

budbro18

Well-Known Member
Just a mockup to try it out, but here is a jury rig we did for trials and to have a unit on hand to help Waywardwolf sort out a complete unit over the phone, that we built in SoCal and which as it turns out, has a defective Mypin controller.

It is in learning mode, so the lower number isn't the set point. That was actually 600F and the nail works slick.View attachment 3151937

Lookin good man! If i were you though id fuck with Auber. 5-10 bucks more than the shitty mypins and they have amazing autotune. As well as constant Ai so if you tune it in a house thats 75 then take it to a friends who keeps his house chilly in the 60s it will compensate for ambient temp and sense the difference in fluctuations and adjust accordingly.

On top of that theyre a US company and have a very nice warranty. Best PID for an Enail on the market today. IMHO

auber SSRs are good as fuck too! same warranty and company.
 
I have Digital E-Nail's for sale now that was put together very similarly to this and has been dialed in to not overshoot and maintains a perfect temp for low temp dabbing at 710 F. If you're interested pm me or check out my page. FULLY CUSTOMIZABLE with any decal and made to order so you know the most precision was put into each unit made just for you!!!

https://www.rollitup.org/t/low-temp-dabbing.828549/
Your charging to much man
 

budbro18

Well-Known Member
For anyone who wishes to contact me ive set up an email for my new site which will be startin up in a month or so.

Please try to contact the email for purchasing info and product info and keep the thread for design/building issues/questions.

[email protected]
 

duval904

Active Member
Your charging to much man
I only use the highest quality coils directly from D-Nail and they have gone through rigorous testing to insure that they heat up evenly and do not overshoot by more than 5 degrees and never drops below 5-10 degrees upon taking a dab with a carb cap. Every box is fully customizable so you can send me whatever picture you would like as a decal and i will wrap your box exactly to your liking. There are two switches: 1 in the back turns the power on to the temperature controller and the 2nd switch in the front turns on the heat to the coil. This way you can have turn off the heat to your coil and still see the temperature as it drops so you know when it is safe to touch or pack up for travel.

Most importantly: These aren't simply homemade DIY E-Nail's. These have been tested and perfected to give the consumer the upmost convenience and performance.

Also, I include a 1 year warranty on the box and a 90 day warranty on the coil.

Let me know if you are interested and maybe you can check out my instagram to see my unit in action.

Instagram name: shatter_box

http://instagram.com/p/n6gd6eFOPx/
 

budbro18

Well-Known Member
I use very high quality parts as well. My coils were made to exact specs we wanted.

My box over shoots by 16F then drops to set temp and sits.

For $250 bucks theres no warranty but i will replace any part for strictly cost of parts. The PID/SSR have a 1 year warranty but i havent worked with aubers Returns and Refunds department so im not sure the conditions in which it fail causing a full refund. Besides that the case is 5 bucks, power cord/inlet should never fuck up.

As for the coils like stated above you will get it for cost. Im workin on the XLR plugs but i really like the hard mounted option for them.

Only downside is if/when the coil eventually does fail youd have to send it back to me VS me sending you a coil.

So my first few boxes have gone to local people so i can make "house calls" in case they have trouble. Those have been tested by heavy dabbers who use them regularly with not fails/complaints in about 2 months maybe more.

Im not knockin your hustle but dont knock mine. People assume just because its lower price that its lower quality parts when im using similar/same parts as many "high quality enails" are using. I just like helping the community VS making money. I make enough to get by dont need a mansion and 6 cars from rippin people off and over chargin.

Just charge 50% less and have 2x the amount of business. Simple as that.

Keep doin your thang like i said not knockin anyone im just doin my thaaaaaang
 
Top