Airwalker16
Well-Known Member
So did you just throw a litter extra wire to the 2nd port on those wagos to connect upto the rocker switch?It'd help to use the @SupraSPL name loader on here. I think it helps notify them better?
So did you just throw a litter extra wire to the 2nd port on those wagos to connect upto the rocker switch?It'd help to use the @SupraSPL name loader on here. I think it helps notify them better?
So those far reds are 1.9-2.1 fv so you could fit quite a few on even a cheap 120-c700. Can you not run more than 700? And is my math right? You could do do like 20 of those 3 pcbs on a 120-c700?cutter has three of these on pcb /with solderless connectors (just sayin) in far red as well
http://www.cutter.com.au/proddetail.php?prod=cut2203
once I get my bars up & guzrl under them that's the next projectSo those far reds are 1.9-2.1 fv so you could fit quite a few on even a cheap 120-c700. Can you not run more than 700? And is my math right? You could do do like 20 of those 3 pcbs on a 120-c700?
I think that's the plan...Do you just wanna put a shit load of those on a panel/heatsink and use it for flower? They're pretty sweet. Can you find a link for far red 660-720nm "uv"er's?
Max Drive current on far reds is 1000maSo those far reds are 1.9-2.1 fv so you could fit quite a few on even a cheap 120-c700. Can you not run more than 700? And is my math right? You could do do like 20 of those 3 pcbs on a 120-c700?
He is a certified vendor for cree they are legitimate .. Don't they would send you knock offs especially the amount you ordered,.Just receive my order from cutter of 2 cxb 3590 but they don't look the same from other pics are those legit?
look like mineJust receive my order from cutter of 2 cxb 3590 but they don't look the same from other pics are those legit?
Thanks again for the support. Just to restate, these are the latest logos on CXB, gold(NEW) vs old black logoThanks guy i feel better now lol the delivery was very fast order sunday get it in my house today
I started a thread on this same question. They're legit.Just receive my order from cutter of 2 cxb 3590 but they don't look the same from other pics are those legit?
I think I'd be more inclined to use these. Lumens are the same but the 4 on these would give a more even spread and a more athstetic pattern in my eyes.cutter has three of these on pcb /with solderless connectors (just sayin) in far red as well
http://www.cutter.com.au/proddetail.php?prod=cut2203
I have a couple of options, the@welight so their 1.9-2.1 on single chips forward voltage so the 3 solderless version would be 5.7-6.3? Is that right? Using any of the drivers we use for Iarger get cobs like cxbs would be just too much to run the only 5-15 3 pcbs Wed need in most spaces. What's a suitable constant current driver for these?
Yeah I posted a link to the 4 chip one you're referring to I think. So no resistors are needed for series? You'd just go positive in, hook a little "U" shaped wire from negative to pos/negative to pos, and a negative line out?also, being that small forward voltage, to run them at 700-1000 MA for the most output as I'd not be running them long AT ALL, what's a suitable driver?I have a couple of options, the
3 up solderless are 3 individually addressable leds(IAD), so each led is powered at 1.9-2.1 or you could then wire(wiring loom) into series or parallel, we also have a 4 up 24mm(not solderless) but can also be IAD or series or parallel. Sorry about so many options, but a lot of these boards are used by the torchys out there who run from batteries, these can all be mounted with Deep reds, Far Reds or we can build custom spectrums for you, red/blue/violet etc. and of course I would be happy if your bought one of everything
Cheers
Mark