The Dawg Father's DIY Vero29 960 Watt 5x5 Scrogg

Airwalker16

Airwalker16

Well-Known Member
Doesnt that driver HAVE to have the right amount of cobs running on it to work right? Unlike the "C" model where you can run say 2-5 cxb3590 cobs on a 240H-C1400B at 1400ma regardless of the # of cobs?
 
The Dawg

The Dawg

Well-Known Member
nevergoodenuf said:
It is a Constant current and a constant voltage. It runs as a constant current until it hits it's voltage limit then converts to constant voltage .
Click to expand...
Airwalker16 said:
Doesnt that driver HAVE to have the right amount of cobs running on it to work right? Unlike the "C" model where you can run say 2-5 cxb3590 cobs on a 240H-C1400B at 1400ma regardless of the # of cobs?
Click to expand...
Correct-A-Mundo Brother Nevergoodenough. I Pmed And E-mailed Companies About The C Model and So Far Only Jerry From Kingbrite Replyed That This Driver Was Currently Unavailable And Didn't Know When They Were Going To Be Stocked. So I Remember Where Robincnn Said This Type Of Driver Would Work. So I Pmed Him For His Help Once Again And Just like Nevergoodenough Stated Once Its Voltage Limit Has Been Reached It Converts To Constant Voltage. Now I Have To Set Each Cob So Its A lot More Work And I Can Still Dim But Only Like A Type Driver Where I Cut The Wattage In Half. I Just Hope I Don't Come Out Looking Like Don King :weed:
 
nevergoodenuf

nevergoodenuf

Well-Known Member
Air- if you look at page 5 of the data sheets, it explains how this works. You would have to run in parallel to run more than one on a driver. This is how all the China lights I have bought are wired. I am not say it's right but I have had no issues running in parallel. The A model will give a wider voltage cap, but would be a pain to dim. I would run no less than 5 COBs on that driver. Worst case, one isn't wired good, or a wire comes loose, the other will only hit 80 watts each. This will protect the rest of the system in case of a COB failure. The only COBs I have had fail are my fault.
 
The Dawg

The Dawg

Well-Known Member
^^^^^^^Correct-A-Mundo Again Brother Nevergoodenough^^^^^^^^ However The Above Driver Is The B Model And I Did Order The A Model. So I'm Covered :hump:
 
The Dawg

The Dawg

Well-Known Member
Damn Little Lover Got Me Thinking About My Nasty Azz Ladies To Which I'm Going To Re-Post. Yes I Said Re-Post You See I Was Smoking So Advance Female Seeds Blueberry Twist Last Night I Swear I Got Higher Than Giraffe Pussy (Even If That's Possible).And I Post These Sexy Azz Ladies Over In the Mini Gorilla Club Thread. I Do Believe I've Found Some New Gear To Run :weed:

Now I'm Going To Address My Heat Problem. After Some Testing I Believe My Problem Lies In My Artic 11 Ability To Properly Cool My Beloved Veros. These Are Nice Little Heat Sinks However Once You Go 0ver 60 Watts Of Cob Power These Little Heat Sinks Struggle To Keep Things Cool. You Can Do It But Its Going To Be Costly. The Reason I Went With These Was Weight Issue And I Was Building A Light Weight High Powered Light. :hump:

Now Without Futher Ado And For The Viewing Pleasure of Those Who Hasn't Gazed Their Eye's On The 9th Wonder of The World :peace:IMG_4126.JPG IMG_4125.JPG IMG_4124.JPG IMG_4123.JPG IMG_4122.JPG IMG_4121.JPG IMG_4119.JPG IMG_4118.JPG IMG_4117.JPG IMG_4116.JPG
 
You must log in or register to reply here.
Top