Is that what your running?I can give you a step by step on how to build a pneumatic one. It's not hard its just tedious to get the calculations correct.
Is that straight off the press or do you do anything after ?Very slow low heating no whipping.
I collect then let sit in room that gets approximately 73degrees for 8-10 hrs. depending on strain/pheno . So no direct heat to butter /crumble it up just ambient room temp. Works great an keeps the flavor intact an super smooth. Was accident really left a 8g slab out (usually keep in fridge )in said area which is my hash making room with walk in closet pre veg clone area an it was butter by morning. Sure you could use hot plate, whip it or vac it low temp. But this is no extra work just let chill an serveIs that straight off the press or do you do anything after ?
They win, this is a far superior press than anything on the market. Granted prep work plays a large roll in it, but it also plays a large roll in any process....I'll take one, where can I order.Sunfire ranch from instagram is about to release a press. All about the pre press and prep.
I've been watching on insta for a while. They have it down for production scale for sure.
I have been following...https://www.instagram.com/sunfire_ranch/ , for a while and he is how I know about it. They have been testing and doing so much cool rosin shit. Then I find out he's apart of ER, and they are making presses. Makes sense for everything they know. They would be the company I would give my money to.They win, this is a far superior press than anything on the market. Granted prep work plays a large roll in it, but it also plays a large roll in any process....I'll take one, where can I order.
Thank youI have been following...https://www.instagram.com/sunfire_ranch/ , for a while and he is how I know about it. They have been testing and doing so much cool rosin shit. Then I find out he's apart of ER, and they are making presses. Makes sense for everything they know. They would be the company I would give my money to.
I like the hardpress too. But the ER is way more commercial IMO.
Prep is very important. They lay it all out and show how to best succeed with their press. I like that.
Not sure how to get one, I would start at their IG...
https://www.instagram.com/elysianresearch/
Rosin works has a good kit, we have had our disagreement in the past but they changed a couple of things, and I would be confident in owning one of their kits on a 10ton+ press.Anyone ordered any digitally controlled plates? Looking to order a kit ready to bolt onto a 2" ram 10 ton or 20 ton press, found some sites but still all 500 and up for the kit, I'm interested in ordering the pid, heating elements and plates seperate and putting together myself as well. Just wondering what everyone else has done, I can get the press whenever. But I would perfer a digital controlled press plate kit for under 500 if it's out there.
If anyone on here makes them pm me and send me quotes.
Also I saw there are two styles, one style looks like I could just order two enails and there are press plates they sell that will accept the flat coil enail.... Is this a good route?
I believe the heating rods embedded in the plates would be much more effective
That is bad ass. What is the price?I have been following...https://www.instagram.com/sunfire_ranch/ , for a while and he is how I know about it. They have been testing and doing so much cool rosin shit. Then I find out he's apart of ER, and they are making presses. Makes sense for everything they know. They would be the company I would give my money to.
I like the hardpress too. But the ER is way more commercial IMO.
Prep is very important. They lay it all out and show how to best succeed with their press. I like that.
Not sure how to get one, I would start at their IG...
https://www.instagram.com/elysianresearch/
I just bought the same set up.....how does it work for you?I just got my 20 ton h frame press, and 3x5 plates from low temp plates. I'll be dry ice extracting all my trim (it's a lot of trim every 9 weeks), then pressing in bags. What sized bags are you using and what temps? I haven't been able to find some numbers.
Press is a harbor freight 20 Tom with grade 10 upgraded hardware, and heated plates from low temp plates.
$4 to $4.5k!!!! Fuck thatI have been following...https://www.instagram.com/sunfire_ranch/ , for a while and he is how I know about it. They have been testing and doing so much cool rosin shit. Then I find out he's apart of ER, and they are making presses. Makes sense for everything they know. They would be the company I would give my money to.
I like the hardpress too. But the ER is way more commercial IMO.
Prep is very important. They lay it all out and show how to best succeed with their press. I like that.
Not sure how to get one, I would start at their IG...
https://www.instagram.com/elysianresearch/
I think I ordered the bigger plates & also ordered their puck mold. I will be pucking dry sieve before squishing...Pretty good. I'll try and source larger baggies, but yeild seems to be decent. I'm playing around with temps. 180, 185, 190. 190 little got for my keif. Tried a bit of it a little while ago and it's very nice.