robincnn
Well-Known Member
Yes I handle the diy side on HLG. Emails and orders. Email me and I will get back asap
DIY with Quantum Boards
- Thread starter robincnn
- Start date
l0wbob2016
Well-Known Member
simply awesome boards !!!
robincnn
Well-Known Member
Will work. Got 600h on way and we will test soon.
Only concern is 150w per board is near max for QB288.
We tested 480h -2100 with 4x QB288 in series and got 510 watts
haze010
Well-Known Member
I plan on getting some of these when more are available, hopefully i wont miss this next batch. I was initially planning on getting the 260w 2 board kit but i had a few questions as im not sure what is going to be the best option for me. With the multitude of drivers and different wiring of series or parallel it can be quite confusing. The initial space i have is 2.5x2.5 but around june i'll have either 4x4 or more to work with and at that point will add more lighting. So basically would i be better off getting the kit now and then later more boards and another driver, or just get 2 boards now and get a driver now that would be good for that future upgrade.
Im sorry if that question seems confusing but english isnt my first language combined with a lack of electrical knowledge and im not sure it makes sense the way i said it.
Basically would i be better getting a different driver with room for future more boards. or just go with 2 drivers in future.
Any advice from more experienced electrical wizards would be appreciated.
Im sorry if that question seems confusing but english isnt my first language combined with a lack of electrical knowledge and im not sure it makes sense the way i said it.
Basically would i be better getting a different driver with room for future more boards. or just go with 2 drivers in future.
Any advice from more experienced electrical wizards would be appreciated.
Nice series is much easier I'll probably go with that thank you
What ma is the 260 watt kit being driven at?
sixstring2112
Well-Known Member
Oh this interests me,this would be series wired then?
sixstring2112
Well-Known Member
Diy with quantum boards good 
1KTrees
Member
Now that's a lot of bamboo
robincnn
Well-Known Member
4x qb288 can go in series on hlg-480-2100
robincnn
Well-Known Member
Hlg240h-1050A in test was running 2xqb304 at 300watts. 1.22 A
Driver factory setting is 1050mA and runs around 260 watts with 2 QB304 boards in series
robincnn
Well-Known Member
You can start with a single 260 kit or 2 of the smaller 90 or 135 kits.
You can add more once u switch to 4x4
And thats running 220 or 120?
Will there be a 3 board kit coming out with the slate 3 triple?
nl5xsk1
Well-Known Member
So chop day, 56 days , cherry pie. Learned a bit, Quantum's are powerful. 34"x44" , 4 quantums on a 320-2800.ran at 300W, too much.1st scrog, started with two plants, ended with one. Next run will be better, having said that, think it is going to be a keeper
Attachments
robincnn
Well-Known Member
Tested at 120
Triple supports 3 boards.may be able to handle HLG320. Will test in 2 weeks
Or 2 boards with space in center.
ChaosHunter
Well-Known Member
I must have missed the slate 3s lol. Where is the info ?
Nice! So assuming the 260w kit was installed on a slate 3; with the space in the center. Would that keep the flowering footprint the same? (2x4) or would the space water it down too much?
Thank you for all your hard work and guidance.
zypheruk
Well-Known Member
It will be fine and surprise the hell outa ya.
How hight from the floor are the lights installed? Thanks in advance.