Club Quantum Board

Mr.Jiujitsu

Well-Known Member
I have a question about those LCD meters. Do you run what's coming in from the AC or the DC side. Say I had 2 drivers I want to be read from 1 LCD. Would I just take the + and - from each driver output and wire them into the appropriate LCD wires? I have been looking into ordering one of those.

I run from my driver DC OUTPUT to my potentiometer- from there my DC goes to the multimeter display - and then it goes to the lights. This gives me read out of what I’m changing. For 25$ or so off amazon you can get both and add it on to most DC applications (within the rated conditions). In my case I used 12 place terminal strip so I could make it easy and have plenty of space between connections. If you want info on anything specific or photos of the wiring I’m happy to help.
 

Aolelon

Well-Known Member
I run from my driver DC OUTPUT to my potentiometer- from there my DC goes to the multimeter display - and then it goes to the lights. This gives me read out of what I’m changing. For 25$ or so off amazon you can get both and add it on to most DC applications (within the rated conditions). In my case I used 12 place terminal strip so I could make it easy and have plenty of space between connections. If you want info on anything specific or photos of the wiring I’m happy to help.
Thanks bro, I think I am going to order one, they look pretty nifty.
 

Mr.Jiujitsu

Well-Known Member
Thanks bro, I think I am going to order one, they look pretty nifty.
These are what I’m running

KNACRO Digital Tachometer PWM DC motor speed controller 30A DC 6V/12V/24V/36V/48V/60V (6v - 60v) Max power 1200W Promise electronic motor switch https://www.amazon.com/dp/B01H6QFUF0/ref=cm_sw_r_cp_api_i_IQC9Ab2X43ZXG

bayite DC 6.5-100V 0-20A LCD Display Digital Ammeter Voltmeter Multimeter Current Voltage Power Energy Battery Monitor Amperage Meter Gauge with Built-in Shunt https://www.amazon.com/dp/B013PKYAV6/ref=cm_sw_r_cp_api_i_cRC9AbYG3ZWZQ
 

Mr.Jiujitsu

Well-Known Member
I get my drives from arrow electronics. Cheapest place I have found with free shipping and sometimes strangely fast delivery
 

Mr.Jiujitsu

Well-Known Member
Is there any benefit of running those drivers over the HLG series?
I’m running them in a cool dry place. They are intended for in cabinet use (metal) but they are safe they just have open terminals that if you stuck your fingers on would shock you. I’ll cover mine with tape, but on the wall where they are there is no way it can happen. I don’t work on anything live at home or at work. Learned when I was younger. The fans haven’t even turned on the drives run so cool. Also they are super inexpensive, I think I got two of the larger LRS for like 55$
 

Mr.Jiujitsu

Well-Known Member
E8D5A3AA-4F0D-431E-997D-9063627E179F.jpeg E8FB6E47-E20E-4847-8F1A-F4FF69F2EE7B.jpeg New veg tent fixture with 1,188 mini suns all built and wired. Waiting for two more potentiometers and then my two stage start to finish scrOG quantum board setup is ready for a full run. Finishing the final touches on environmental controls before I germinate some new
 

Humple

Well-Known Member
View attachment 4134597 View attachment 4134596 New veg tent fixture with 1,188 mini suns all built and wired. Waiting for two more potentiometers and then my two stage start to finish scrOG quantum board setup is ready for a full run. Finishing the final touches on environmental controls before I germinate some new
Nice to see that I'm not the only one who doesn't bother to remove the stickers on my aluminum channel!

Beautiful fixture, man. What driver are you using?
 

Mr.Jiujitsu

Well-Known Member
4648A04B-15B9-4FF7-8603-4A2207982FA6.jpeg
Nice to see that I'm not the only one who doesn't bother to remove the stickers on my aluminum channel!

Beautiful fixture, man. What driver are you using?

I’m using the lrs 350 36 for two sets of 4, and lrs 75 36 to run the middle. Same setup as my flower tent just different spectrum. The veg has 8 4000k and the center is 2700k.

I have a bunch of various spectrum boards so the next one will be more mixed.

The right side of the photo is the driver setup for the new light.
 

hybridway2

Amare Shill
View attachment 4134597 View attachment 4134596 New veg tent fixture with 1,188 mini suns all built and wired. Waiting for two more potentiometers and then my two stage start to finish scrOG quantum board setup is ready for a full run. Finishing the final touches on environmental controls before I germinate some new
Very nice! Shit I want one. Except I'd drill holes in the boards & add some color. Or attach some small mix color strip.
Not a scientist but for me the right enhancement seems to help allot w/ the deficiencies Cal-mag has NOT been the answer for me.
Mag, & ,N are big helpers along w/ mixed lighting. I do strongly believe that those using the right nutes from the start wont even have a deficiency problem at all under all white led.
Unfortunately, I'm not that guy.
 
Top