Boards that can use 240-1750

Airwalker16

Airwalker16

Well-Known Member
Hey guys, I find myself wanting to re use the 2 HLG-240H-C1750B meanwell drivers I've got on my current build, for sosomething new...I recently built a new fixture and am now finding myself daydreaming of doing it again.
I'd like to use boards, strips I could handle too.

But these drivers I'm finding are hard to pair with a setup that would be maxing them out.

Do any of you have any recommendations on strips or boards that would get me the Max out of with a 1.750ma current?
 
Major Blazer

Major Blazer

Well-Known Member
Sorry, I did that backwards. We all blaze here. But yeah, you can get real creative that way. I have a spare HLG-120h-c1400 and am in the same boat with a strip build.
 
Airwalker16

Airwalker16

Well-Known Member
Major Blazer said:
Sorry, I did that backwards. We all blaze here. But yeah, you can get real creative that way. I have a spare HLG-120h-c1400 and am in the same boat with a strip build.
Click to expand...
You mean by splitting the current In Half to 875MA? That would me it even harder to find anything with enough luminous flux to compare to the 8 cxb3590's pushing 11K ec totaling near 90K.
 
Major Blazer

Major Blazer

Well-Known Member
You could get 6 l09 h influx on each driver that way, they’d be super efficient, flux for each is gonna be around 8000+ in 3500k (8000x6x2=96000).
 
Airwalker16

Airwalker16

Well-Known Member
Major Blazer said:
You could get 6 l09 h influx on each driver that way, they’d be super efficient, flux for each is gonna be around 8000+ in 3500k (8000x6x2=96000).
Click to expand...
Even with the $32 ones that's $400 just on strips. There's gotta be some other way..
Even buying 4 Atreums with sinks at $70/4=280+hlg-600h-54a=4
$420. If I was gonna spend that much, i would go that route.
But there has to be some strip or board out there I can make work with these damned 240-1750's!!!
 
Rocket Soul

Rocket Soul

Well-Known Member
Airwalker16 said:
Hey guys, I find myself wanting to re use the 2 HLG-240H-C1750B meanwell drivers I've got on my current build, for sosomething new...I recently built a new fixture and am now finding myself daydreaming of doing it again.
I'd like to use boards, strips I could handle too.

But these drivers I'm finding are hard to pair with a setup that would be maxing them out.

Do any of you have any recommendations on strips or boards that would get me the Max out of with a 1.750ma current?
Click to expand...
Meijiu 312 boards are 36V so matches fine with meanwells cc range. Actually they will prob run even lower at 1750, maybe 34V.
 
Airwalker16

Airwalker16

Well-Known Member
I'd really like something with a high voltage(50-70) but most importantly, something that maxes out around the 1750ma range if possible. That would be ideal.
 
Rocket Soul

Rocket Soul

Well-Known Member
Airwalker16 said:
I'd really like something with a high voltage(50-70) but most importantly, something that maxes out around the 1750ma range if possible. That would be ideal.
Click to expand...
there really isnt anything like that on alibubbers. it would mean a board running around 70V, i think that voltage is only 72V crees, and vero 29 C.

the way i figure the china boards in order to be competetive with real QBs: running them at nominal (60w/board for these) is a good way to make up for not being lm301b top bin diodes. 2x china boards at 60w each is similar in efficiency to a 120w qb, but cheaper and you can hang them lower and spread the light better.
 
SSR

SSR

Well-Known Member
mathewscott said:
Thing is. Typical Alibaba you have to buy 10 to get a decent price
Click to expand...
Yeah but 10 of em over a 4x4 at around 600w total is wayy cheaper than QBs and just as efficient with a better light spread and the ability to run closer to the canopy for height restricted folks.
10 isn't that big an order when you think about it tbf
 
You must log in or register to reply here.
Top