That sounds lovely.View attachment 4293482
#dulcecherrypunch f1 smells of fruity pebbles & trix when you move the bag..
The nugs when handle smell of cherry pie cookie funk.
Cure time.
DibsView attachment 4293482
#dulcecherrypunch f1 smells of fruity pebbles & trix when you move the bag..
The nugs when handle smell of cherry pie cookie funk.
Cure time.
Getting chunkyDay 42View attachment 4293480
GMO x swayze
View attachment 4293481
Funky smells off both the top pic, the smell that plant is giving off is rank like a rotten armpit haha, I’m spewing i missed a nana on the top on, I’m gonna have a few seeds but I’m gonna make a lot of bubble hash for my rosin press. I’m not phased
I use to run the cheap yellow ones and store them in the 7 calibration solution I’d buy two at a time to test for accuracy.Exaust fan went out - temps hit 102. When I was out watching my daughter perform. No visible damage except some tacoing on a couple of plants.
Tried to calibrate my multimeter and the damn pen was reading 8.2 with the 7.0 calibration solution, wouldn't recognize. Been running my plants in the low 5's for who knows how long. Gotta run into town and buy another.
Is there any recommendations on a favorite pen?
Used the hanna's and a Milwaukee for a while.Grabbed the blue lab ppm and tds pen kit from fleabay.They work well.Exaust fan went out - temps hit 102. When I was out watching my daughter perform. No visible damage except some tacoing on a couple of plants.1
Tried to calibrate my multimeter and the damn pen was reading 8.2 with the 7.0 calibration solution, wouldn't recognize. Been running my plants in the low 5's for who knows how long. Gotta run into town and buy another.
Is there any recommendations on a favorite pen?
I let the flowers get super crispy and then roll/crush them on a tilted tray, let the seeds roll down to the lower side. I don't normally worry about the left overs. I tend to flower small plants or only dust a flower or two, so I don't have a ton of left overs to start with. The first chuck I ever did resulted in enough beans to feed the planet for at least two generations, I toned down significantly after that.woo, harvested momma tonight, gonna let it dry for a week and a half or so, then start picking out the beans! do ya'll just tear the plant apart, take all the beans out, and then just save it for personals? or just pick out what you can see and leave nugs intact? any preferred harvesting method? thanks!
100 ante to bad , 160 will bubble paint tho.Exaust fan went out - temps hit 102. When I was out watching my daughter perform. No visible damage except some tacoing on a couple of plants.
Tried to calibrate my multimeter and the damn pen was reading 8.2 with the 7.0 calibration solution, wouldn't recognize. Been running my plants in the low 5's for who knows how long. Gotta run into town and buy another.
Is there any recommendations on a favorite pen?
I have a blue lab and a cheap 80 dollar tds combo meter from amazon, I like the combo meter better and I think if I stay on top of calibration it will be just fine.Exaust fan went out - temps hit 102. When I was out watching my daughter perform. No visible damage except some tacoing on a couple of plants.
Tried to calibrate my multimeter and the damn pen was reading 8.2 with the 7.0 calibration solution, wouldn't recognize. Been running my plants in the low 5's for who knows how long. Gotta run into town and buy another.
Is there any recommendations on a favorite pen?
I know, I could have burnt the house down!@Bakersfield
What if you where not able to get home?
You should think about adding a fail safe controller like this
View attachment 4293881
(Pretty sure your running DEs)
Once the temps get to hot, it will start dimming the lights , if the temp keeps climbing , it will start turning them off .
I’m going to play with the sun rise n set too.
50-115% to 115- 50%