Samsung 1 footer build driver suggestion

S

Seriousbuds

Active Member
I had some extra 1 footer Samsungs layring around and I'm going to throw 6x inFluxs on an old grill plate as my heatsink; but I'm stumped on what driver to pick to run all 6 of them, as these strips only pull 9.05v each and should be ran at around 1050ma.

Does anyone have some suggestions on the best driver to run 6 of these strips?

Thanks
 
Airwalker16

Airwalker16

Well-Known Member
friedguy said:
HLG-80H-54A
Click to expand...
They're 9v.... A 54v driver would have to use 6 in series to get to the 54v. And then they'd all share that current.

Use an HLG-80H-12A.
You'll need to turn the voltage pot down to 9v but then you'll be able to run them all in parallel and it will split that drivers 60w/5a amongst all 6 strips.

9VX1.050ma=9.45w per strip. 9.45wX6strips=56.7w.
 
friedguy

friedguy

Well-Known Member
Doesn't the HLG-80H-12A only goes down to 10.8V? Series or parallel... sharing current or sharing voltage... either way man.
 
S

Seriousbuds

Active Member
friedguy said:
HLG-80H-54A
Click to expand...
You're a gentleman and a scholar.

If you were gonna do a 2019 build, what would your goto cheap setup be if I wanted to build another 2 or 3 6x 1" LED fixtures with cheap LEDs and drivers?

Light output/PPFD isn't a priority as I'm going with microgreens - I'm primarily concerned with the cost to light each shelf.
 
Airwalker16

Airwalker16

Well-Known Member
Seriousbuds said:
You're a gentleman and a scholar.

If you were gonna do a 2019 build, what would your goto cheap setup be if I wanted to build another 2 or 3 6x 1" LED fixtures with cheap LEDs and drivers?

Light output/PPFD isn't a priority as I'm going with microgreens - I'm primarily concerned with the cost to light each shelf.
Click to expand...
Don't use the 54a
 
S

Seriousbuds

Active Member
Airwalker16 said:
They're 9v.... A 54v driver would have to use 6 in series to get to the 54v. And then they'd all share that current.

Use an HLG-80H-12A.
You'll need to turn the voltage pot down to 9v but then you'll be able to run them all in parallel and it will split that drivers 60w/5a amongst all 6 strips.

9VX1.050ma=9.45w per strip. 9.45wX6strips=56.7w.
Click to expand...

Thanks for the reply, I'll go with this driver.

If you had to buy more of these 1" lights and drivers, what would you do for a more current build, with cost being the main concern? I'm planning to build a few more of these 1" x6 fixtures (has to be 1' as I have 3' long aluminum grill plates that I'm reusing as heatsinks)... I'm lighting shelves for microgreens so they don't need an assload of light.

Cheers
 
Airwalker16

Airwalker16

Well-Known Member
Seriousbuds said:
Thanks for the reply, I'll go with this driver.

If you had to buy more of these 1" lights and drivers, what would you do for a more current build, with cost being the main concern? I'm planning to build a few more of these 1" x6 fixtures (has to be 1' as I have 3' long aluminum grill plates that I'm reusing as heatsinks)... I'm lighting shelves for microgreens so they don't need an assload of light.

Cheers
Click to expand...
I would get the cutter sol strips. They're 22" but such a great price.
 
1

1212ham

Well-Known Member
Airwalker16 said:
They're 9v.... A 54v driver would have to use 6 in series to get to the 54v. And then they'd all share that current.
Click to expand...
Whats wrong with that?

Airwalker16 said:
Use an HLG-80H-12A.

You'll need to turn the voltage pot down to 9v but then you'll be able to run them all in parallel and it will split that drivers 60w/5a amongst all 6 strips.

9VX1.050ma=9.45w per strip. 9.45wX6strips=56.7w.
Click to expand...
The HLG-80H-12A is rated at 5 amps..... 5 amps/6 strips = only 830ma per strip, not 1050ma.
 
1

1212ham

Well-Known Member
No, I don't. The primary purpose of parallel builds is avoiding the high voltage of series wiring, but 54v isn't high voltage.
 
Last edited:
S

sethimus

Well-Known Member
Airwalker16 said:
Use an HLG-80H-12A.
You'll need to turn the voltage pot down to 9v but then you'll be able to run them all in parallel and it will split that drivers 60w/5a amongst all 6 strips.

9VX1.050ma=9.45w per strip. 9.45wX6strips=56.7w.
Click to expand...
yo einstein, what's that in the spec sheet? keen to elaborate how exactly you would turn that voltage adjuster lower than the range mentioned in the spec sheet?

Screenshot_2019-04-03-14-25-38.png
 
You must log in or register to reply here.
Top