Northern Lights Waterfarm

Dr.Amber Trichome

Well-Known Member
Fingers crossed that you get them quickly. Are you planning on switching to a local vendor?
Got em today! They all made it safely NOT crushed, wrapped up tightly in a small taped plastic baggie and in a tight roll and then put into this cheap iridescent wallet with a broken zipper. So I immediately placed one on a wet paper towel between saucers and into my closet with a small space heater under it. Hopping for a fast germ.
3389E7D0-ACB4-45C1-BC51-D21E80E4CF9D.jpeg
57394AD0-9C7A-49D1-A1A1-CC750B9C2AC3.jpeg
 

Jimdamick

Well-Known Member
Hello!:bigjoint:Welcome to my 11th waterfarm grow. I haven’t done one in 4 years, but I am very excited to get started again because I have some great new gear!

I will use my 4x2 Gorilla Grow Tent with a feminized Northern Lights.

I got my new VATA
Reverse Osmosis water filtration system yesterday
And my new waterfarm reservoir and clay pebbles yesterday as well. I am currently washing the pebbles off in the shower.

View attachment 4388265
View attachment 4388266
View attachment 4388268
:peace:
Don't put pebbles in the bottom of the container, they are not needed, and interfere with the uptake of the tube.
 

Dr.Amber Trichome

Well-Known Member
Good to see your grow back on track Doc!!
Thanks Dusty! Every thing is going well . I had to reset my light timer a few times and watching it for 4 am shut off tomorrow . Pulled 200 ppm from the res after the first night run with the nutes. I’m fine with that strength and she seems to be responding well , very perky and pushing up with energy.bongsmilie8-)
I’m working on these paintings her room. It’s my art studio/grow room.
So she gets a lot of attention. If everything stays on track I will be having a Christmas Harvest!!
E5416DD4-A803-423E-8FFF-BDB533716EBA.jpeg
 

horribleherk

Well-Known Member
Thanks Dusty! Every thing is going well . I had to reset my light timer a few times and watching it for 4 am shut off tomorrow . Pulled 200 ppm from the res after the first night run with the nutes. I’m fine with that strength and she seems to be responding well , very perky and pushing up with energy.bongsmilie8-)
I’m working on these paintings her room. It’s my art studio/grow room.
So she gets a lot of attention. If everything stays on track I will be having a Christmas Harvest!!
View attachment 4397878
A very merry Christmas indeed!!!
 

Dr.Amber Trichome

Well-Known Member
Got all my scrog screen materials today. Now I need to design a pattern to paint the wooden frame .
I have had pink and green ones Before.
2E3CF4CB-C63C-4988-92DF-9ED565CAC1C0.jpeg
Here is a picture of my previous scrog screens.
2DBACB6F-D32A-4760-A5C1-86638DCB15A6.jpeg
No stickers this time because they end up falling off .

I did my first res change because there was quite a bit of pebble dust in the bottom res and my PPMs creeped to 230.
 

DustyDuke

Well-Known Member
Got all my scrog screen materials today. Now I need to design a pattern to paint the wooden frame .
I have had pink and green ones Before.
View attachment 4398556
Here is a picture of my previous scrog screens.
View attachment 4398557
No stickers this time because they end up falling off .

I did my first res change because there was quite a bit of pebble dust in the bottom res and my PPMs creeped to 230.
Love the skulls
 

Dr.Amber Trichome

Well-Known Member
Timber chat room note:
You will want to start conservatively since the COBs are quite powerful and can be operated closer to the plants than HID because they emit little/no IR.We recommend starting at 24-36" above the canopy @ 25-50% output for vegetative growth, gradually lowering the light to 18" above the canopy and 100% output for flowering.Pay close attention to the health of the leaves, especially, as they will be a good guide to how well the plant is tolerating the power.

I am at 36 inches above and at the lowest dial in for light power.
 

Dr.Amber Trichome

Well-Known Member
1080701B-8470-474C-BD3B-0C86E0B66D4A.jpeg

Day 8bongsmilie
Rez change :eyesmoke:
PPMs in 420:leaf:
:-D
My R/O water has 140 ppm because one of the filters in the machine has cal mag added.
:-P
Added 1.5 ml Flora Nova Bloom
:-P
Added 2 ml Cal Mag
:-P
Added 3 ml H2O2
:-P
Ph is 6.4
:-P
4138CD89-74AE-4ECF-81D5-9144CBB8F058.jpeg
Pulled quite a bit of water into my little dehumidifier.
C6A133EB-37D9-413D-8F00-ECA2B18A3A7E.jpeg
Temps staying between 74 degrees and 82degrees 24/7
Humidity here averaging 50 degrees.
:cool:
Painting my Scrog frame.
:bigjoint:
441CF293-37E0-4F30-B3C4-447DE98B5688.jpeg
:peace:
Namaste
 
Top