I can answer most questions about electrical problems and such i am a commercial/residential sparkyView attachment 4788198
if you must use it and you have a bunch of it my suggestion would be to double or even better triple it up to be safe and make sure your connections are tight be careful when stripping it bach not to knick the wire try a test run and turn on the light the wire shouldnt get warm at all but if it was me i would buy some 14 and do it right 22 is only good for 3 amps maxWell I just asked in another 'expert electrician' thread, so perhaps you can help, i'll just copy/paste ...
I am waiting on some HLG QB120 boards (70W each) and a user here @ilovereggae is helping me out with some drivers, wagos, etc. etc. (very much appreciated btw). I will be wiring 2 boards in parralel on one driver (Delta LNE-24V120WDAA) with a potentiometer.
The only thing I have left is the wire to use on the DC side. I have tonnes of 22 gauge wire that I use with my arduino and rasp. pi microcontrollers. Would this wire be sufficient/safe enough to carry the load this setup will produce?
The only source of information I could find on the National Electric Code on maximum rated amperage for a given wire gauge only goes as 'low' as 14 gauge wire, it doesn't show the max amperage for anything above (thinner) then 14 gauge:
wiresizecalculator.net
it depends on where they are going to be if they are enclosed in a small box in a warm enviroment then yes i would but you have the right idea about mechanical ones they will fail faster in my opinionWhen using higher amperage solid state relays eg: 20-30 amp relays is a heatsink necessary?
In this case I am using 2 30 amp relays in a box controlled by an arduino that will turn on and off the AC. Really I probably just need 15 amp relays, but they were hard to find in solid state (the AC and heater will probably cut on a lot so I wanted to avoid mechanical for longevity).
Good to have another fellow sparky on board, I'm pretty rusty as I have focused on growing weed for the last 20 years. We have a thread that you should get into since it's become the go to thread for electrical advice.I can answer most questions about electrical problems and such i am a commercial/residential sparkyView attachment 4788198
Is that a flux capacitor?I can answer most questions about electrical problems and such i am a commercial/residential sparkyView attachment 4788198
Lol. three phase transformer.Is that a flux capacitor?
Looks the same to me.Lol. three phase transformer.
I want some of what you are smoking! lolLooks the same to me.
He's just missing the Delorean.
Hi. I want to build 3 plc lights and I’m gonna have more stuff like dehumidifier fans and things like that. How do I know if my apartment can take all this loadI can answer most questions about electrical problems and such i am a commercial/residential sparkyView attachment 4788198
Get the wattage draw of each appliance..wattage x volts = amp draw.Hi. I want to build 3 plc lights and I’m gonna have more stuff like dehumidifier fans and things like that. How do I know if my apartment can take all this load
You gotta train them bitches to not touch things that ain't theirs!How do I make a mains supply zapper to zap thrips and mites without harming the plants
I take it no one has put a +and - to a spidermite to see how many volts make it explode, or is it the ampsYou gotta train them bitches to not touch things that ain't theirs!
Looks like its got 1.21 giga watts!!Is that a flux capacitor?
well if i ever get them again i will try it but i hope that day doesnt come every watering i spray neem oil and insect soap at the base of my plant then pluck several leaves from each plant and check them under a scope homey aint playing that game againI take it no one has put a +and - to a spidermite to see how many volts make it explode, or is it the amps
Nope, wattage/volts = amp draw. Volts x amps = watts. I won't complicate it with power factor.Get the wattage draw of each appliance..wattage x volts = amp draw.
Then see what breakers are on the circuits you want to use and how many amps they are.
Add up the appliances amp draw you want to put on each circuit and dont exceed 80 percent of amps that the breaker is for each circuit.