A bit overgrown -- what to do? (Dosidos, Runtz etc)

[Overgrowtho]

These have been in flower for just 10 days. They are still stretching and unfortunately my lights can only go so high. Any suggestions?

I should have flipped to flower a week earlier or used 8 instead of 10 plants! I know its a bit too much of a jungle. So I've tried to clean up the bottoms and even cut off some of the tops and cleared out places with too dense fan leave foliage.

Any ideas please? How can I keep these on point?

 

[.Smoke]

Supercropping: Magic Technique to Control Cannabis Plant Height | Grow Weed Easy

by Nebula Haze How Does “Supercropping” Control Tall Cannabis Plants? Supercropping (or “super cropping”) is a specific bending technique that is used to control the height and shape of out-of-control cannabis plants by bending branches at major angles. The marijuana supercropping technique lets...

www.growweedeasy.com

 

[Driver733]

Nice mess! Raise the lights and lower the drain table.

 

[bam0813]

Maybe the pic is deceiving, but it does look like there is plenty of room to raise lights

 

[bk78]

You have 3+ feet below the plants, and it looks like 4+ above the plants? I don’t see a issue at all here. Grow trees

 

[bam0813]

Imo if you ran a galv. Cable with a turn buckle you could eliminate the slack in your rope?setup

 

[McShnutz]

I'd lollipop everything, prune out any small twig branches. And after all that's done, then go back and "pinch" or crush, all the mains. Break the vascular system, this will keep all the nutrients focused in the tops. Keep lights closer to minimize stretch.

 

[bk78]

. Break the vascular system, this will keep all the nutrients focused in the tops. .

Huh?

 

[Mr_X]

Buy some ceiling hooks and raise your lights. This has happened to me before, but in my grow tent. I ended up moving my carbon filter from hanging on top to letting it sit on the floor so i have space to raise my lights.

 

[McShnutz]

Supper cropping is going to leave a shit load of overlay, blocking light from penatrating and cutting down airflow to flower sites.

 

[McShnutz]

Huh?

Zylem and phloem, probably spelled wrong.

 

[Overgrowtho]

Imo if you ran a galv. Cable with a turn buckle you could eliminate the slack in your rope?setup

Thanks guys, I like the idea of the turnbuckle. I am understading that: to just run the cable through the existing light hangers and wall hooks, then tighten the turn buckle?

Supper cropping is going to leave a shit load of overlay, blocking light from penatrating and cutting down airflow to flower sites.

I agree. I am reluctant to try it.

I'd lollipop everything, prune out any small twig branches. And after all that's done, then go back and "pinch" or crush, all the mains. Break the vascular system, this will keep all the nutrients focused in the tops. Keep lights closer to minimize stretch.

Agreed except not sure how the vascular system breaking will help anything? Please unpack

 

[bam0813]

Yup just get a couple crimps. They look like mini muffler clamps. That’s how you make “loop” in cable . Pull tight then the turn buckle makes it taught

 

[bam0813]

 

[McShnutz]

Agreed except not sure how the vascular system breaking will help anything? Please unpack

In the past when I've pinched it did slow down the stretch. I could have been the strain I was growing at the time but the only stretch I gained was pure cola stacked with flower.
I feel like the "injury" greatly minimized the plants focus on vertical gains and instead it focused on healing. This coupled with keeping the lights closer to control stretch.

 

[Daddymcdank]

These have been in flower for just 10 days. They are still stretching and unfortunately my lights can only go so high. Any suggestions?

I should have flipped to flower a week earlier or used 8 instead of 10 plants! I know its a bit too much of a jungle. So I've tried to clean up the bottoms and even cut off some of the tops and cleared out places with too dense fan leave foliage.

Any ideas please? How can I keep these on point?

Id start by smashing that table to pieces. I’d get so frustrated always having to work around that.

 

[McShnutz]

Id start by smashing that table to pieces. I’d get so frustrated always having to work around that.

Aww shit, we got another MC up in here.

 

[coralreefer999]

I agree. I am reluctant to try it.

I used these 'plant trainers' with decent success (small size). They allowed me to bend the stems without breaking them. The plant does seem to raise the entire branch to compensate, but between the trainers and the net I was able to keep them under control with lots of colas.

 

[Daddymcdank]

I used these 'plant trainers' with decent success (small size). They allowed me to bend the stems without breaking them. The plant does seem to raise the entire branch to compensate, but between the trainers and the net I was able to keep them under control with lots of colas.



View attachment 5097863View attachment 5097862View attachment 5097861

No need for those trainers or lst, just gonna cause herms. Do more topping and no lst, just IMO

 

[McShnutz]

Low stress training stresses to the point of hermi?
High stress training like topping doesn't?
Hmmmm