Diy rosin press

Jjgrow420

Jjgrow420

Well-Known Member
smokey0418 said:
To be honest, it is a very great service imho. Usually can have a package in 2-3 days after it’s arrival to the USA facility.

So far a caged unit looks promising to ship soon.
Click to expand...
Ya I just ordered through them. Still will save me a bunch of coin. Remember the caged plates are for an a frame press (I think). A ram press you need the uncaged plates.(pretty positive)
 
smokey0418

smokey0418

Well-Known Member
Jjgrow420 said:
Ya I just ordered through them. Still will save me a bunch of coin. Remember the caged plates are for an a frame press (I think). A ram press you need the uncaged plates.(pretty positive)
Click to expand...
Ram should come down fine , right into the circle they provided.
I think the main thing is just the proper alignment that a cage will provide.
Either way , Dank will be squeezed from these units.
 
W

waterproof808

Well-Known Member
Jjgrow420 said:
Ya I just ordered through them. Still will save me a bunch of coin. Remember the caged plates are for an a frame press (I think). A ram press you need the uncaged plates.(pretty positive)
Click to expand...
No, Caged plates arent specific for A-frame presses, low-temp plates actually says their plates are not compatible with 6-ton a-frame presses because there is not enough clearance.

The main benefits of caged presses is plate alignment is not an issue and it reduces heat transfer to the ram since the plate is not attached to your ram. When your plate is attached to the ram, the heat travels up the ram pretty quickly and can cause your hydraulic fluid to thin and possible leak through the seals. I use a small scrap of OSB on top of my plate and a piece of g10 insulation on the bottom to minimize heat transfer to my press.

The downside to a caged press, is that there is not enough clearance to do "bottle technique" but you can fix that by getting longer bolts/springs.
 
Jjgrow420

Jjgrow420

Well-Known Member
waterproof808 said:
No, Caged plates arent specific for A-frame presses, low-temp plates actually says their plates are not compatible with 6-ton a-frame presses because there is not enough clearance.

The main benefits of caged presses is plate alignment is not an issue and it reduces heat transfer to the ram since the plate is not attached to your ram. When your plate is attached to the ram, the heat travels up the ram pretty quickly and can cause your hydraulic fluid to thin and possible leak through the seals. I use a small scrap of OSB on top of my plate and a piece of g10 insulation on the bottom to minimize heat transfer to my press.

The downside to a caged press, is that there is not enough clearance to do "bottle technique" but you can fix that by getting longer bolts/springs.
Click to expand...
Ahh thank you for clearing that up
 
smokey0418

smokey0418

Well-Known Member
i had to chuckle, dabpress fulfilment by Amazon at about 100 skins in my pocket for other items needed.
It pays to look around.
 
manfredo

manfredo

Well-Known Member
Jjgrow420

Jjgrow420

Well-Known Member
Well my plates are a 25min drive away in the States but I have to wait till they ship them an hour and a half away from me then ship them back the same way to my house. Lol. Thanks @smokey0418 for the shippsy tip. I'll be using that again for sure.
 
Last edited:
Jjgrow420

Jjgrow420

Well-Known Member
manfredo said:
I built a 20 ton for under $400, with a Harbor Freight press on sale for $150 and plates from Vevor, which is a semi-sleazy Chinese company. It works great!!

www.vevor.com

Rosin Press Plate Kit 4"x7" Rosin Extractor 4 Heating Rods 10-20 Ton Hydraulic | VEVOR US

Shop Rosin Press Plate Kit 4"x7" Rosin Extractor 4 Heating Rods 10-20 Ton Hydraulic at lowest price, 2-day delivery, 30-day returns. Shop now at VEVOR.
www.vevor.com www.vevor.com


View attachment 5130292

View attachment 5130293
Click to expand...
Great deal on the press man. If I didn't have so much Canadian Tire money I would have shopped around a bit, but really I only paid 100bucks for the press after all was said and done so not too shabby. My whole idea was 'cheap but good'. I'm still under 400 total something like 330 (for the press, pid and plates) after fees and duty for the plates
 
manfredo

manfredo

Well-Known Member
Jjgrow420 said:
Great deal on the press man. If I didn't have so much Canadian Tire money I would have shopped around a bit, but really I only paid 100bucks for the press after all was said and done so not too shabby. My whole idea was 'cheap but good'. I'm still under 400 total something like 330 (for the press, pid and plates) after fees and duty for the plates
Click to expand...
The bad thing about it is it is not portable. But it does work well, for about a year now.
 
smokey0418

smokey0418

Well-Known Member
Jjgrow420 said:
Well my plates are a 25min drive away in the States but I have to wait till they ship them an hour and a half away from me then ship them back the same way to my house. Lol. Thanks @smokey0418 for the shippsy tip. I'll be using that again for sure.
Click to expand...
When there outlet was 1.5hr away I would in most cases use the forwarding option once it arrives and payment is due. Just another option for customers to get there items with ease through shippsy.
 
You must log in or register to reply here.
Top