Search results

  1. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    The problem has stopped spreading for the most part. Some of the leaf sets that were affected did still die completely. There are a few new leaves at the tops of the buds that look good. A few of the plants started to yellow a bit so I'm going to give them a feed today, I'll go 75% of normal...
  2. P

    Bubble Hash price

    Do you separate it by microns or do you mix it all up and sell it as a puck?
  3. P

    Bubble Hash price

    Is anyone taking their trim and making bubble hash? What are you charging to produce it?
  4. P

    Feds Threaten State Dispensaries Nationwide

    It doesn't say anything about dispensaries in the law here either.
  5. P

    Income tax

    The standard.
  6. P

    Income tax

    How do you guys handle caregiving income on your taxes? I do want to claim my income and tax but I don't want to create receipts that list patient/dispensary names. I wonder if I'll be safe doing so.
  7. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    I hven't seen any real changes same shit is still f'd and spotted, som eof the lowers are yellowing and flaling off. The folier which was Magic Gree3-.1-.4 didn't do much or pretended incoming problems unseen.
  8. P

    Plants dying on first grow - Help!!!

    I looked, I don't see anything about temps or ventilation, so there's more input. The chart is helpful as well I think.
  9. P

    Plants dying on first grow - Help!!!

    http://www.stealthgrow.com/images/nutrient-ph-range.jpg I can't speak to the accuracy of the chart but it gives you an idea of what happens when your pH isn't correct.
  10. P

    Plants dying on first grow - Help!!!

    http://www.google.com/imgres?imgurl=http://www.stealthgrow.com/images/nutrient-ph-range.jpg&imgrefurl=http://www.stealthgrow.com/grow-room-setup.htm&usg=__mocJyGbfrS37hzOizO3Uck4_Pq8=&h=407&w=325&sz=24&hl=en&start=0&zoom=1&tbnid=_PrB-ijRtJygTM:&tbnh=158&tbnw=127&ei=J--CTZagO4qugQfC19nMCA&prev=/im...
  11. P

    Plants dying on first grow - Help!!!

    I'm almost a complete newb, I'm on my third grow so take what I say with a grain of salt. Your temps are too high, your pH is too high, you're watering too often, and you need a lot more ventilation.
  12. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    Me too! I flushed each plant with 2.5 gallons, which is all I could fit, four times. I had to use water from my old dechlorinator/sediment filter because my RO system doesn't put out enough water. I finished an hour past lights out. I'm going to give them some Green Magic foliar feed in the...
  13. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    The run off is a little over 5, flush?
  14. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    I'll go check my runoff now and flush if it's off. How close should my run-off be to what I put in?
  15. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    I'm pretty sure it's not K, it doesn't look like any of the real life pictures I've seen of it and the problem doesn't start on the outer edges of the leaf. I am thinking whatever problem they have it's being compounded by heat stress or bleaching, I think that's causing some of the yellowing...
  16. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    I haven't checked my runoff recently but I have in the past and it's always waay lower than the 6.2 water and feed I'm putting in.
  17. P

    Rust Spots Turning Into Brittle Yellow/Brown Leaves.

    Week 5, the problem doesn't normal strength. I use drip clean and just started using magic green. I see very few light rust spots during veg then midway through flower it hits the tops of the plants under the light(the larger ones).
  18. P

    Tricking my climate controller into thinking it's daytime all the time.

    RadioShack had a battery holder and a white LED, that with some tape solved the problem.
  19. P

    Tricking my climate controller into thinking it's daytime all the time.

    The cord is to short to move just the sensor, I can't move the unit because it needs to be by the CO2 burner, which is on a short line from my gas main.
Top