Search results

Same! It’s not tooooo bad but not cheap. Works though. Wasn’t looking into trying some thing else like sugaree or sour D others rave about or the snow storm. You use any carbs?

Do any of you use any supplemental carbohydrates and resin enhancers with H&G such as sugar daddy or sugaree and terpinator or like carboload and snowstorm? Or is one of there products in the line similar that i am not recognizing? I also heard sea green compliments well.

@Sativied I gotcha and thanks for the sharing and info....you and @a mongo frog are OGs on this thread 2009! Man life flies, hope everyone is well. @calvin.m16 I agree with your statements go with what is the right choice for medium. Does everyone find that airstones in general will always...

That's really cool and thanks for the snippet. So I wonder if one can conclude that with promix hp (peat base with perlite only) hydro may be superior to the aqua flakes and to run coco with coco media. However, the caveat that aqua/coco/and hydro could all be used with very close results in...

Gotcha...I read the last post wrong.

@a mongo frog when using the aqua flakes vs coco were the ppms/ec the same or was it lower using aqua? Asking because description on their site says low ppm blah blah @Sativied are you still using this line? Your making me wonder with the statement that uptake is better using the hydro because...

Okay so for promix hp (no coco in it) and/or mothers earth coco potted....could technically use coco/hydros or aqua flakes? I keep hearing aqua flakes as best to use for promix hp (peat base no coco) even in drain to waste and the coco for coco which we have used with good results. But when they...

Hello, Maybe this is a question for @a mongo frog @purrrrple I have been trying to figure it out the specific differences with the bases: coco/soil/aqua/hydros. Besides the obvious coco for coil and soil for soil. Why is it that some people use aqua flakes in promix and could you use coco base...

@GBAUTO I got the trolmaster..aka a dimmer+ up and running and to my findings I had to limit voltage so that in case one board went out current remained the same. But upon doing so the dimmer did not respond to dimming until it reached 60% and under which I believe since this is a CV driver...

@GBAUTO so after 24v constant current kicks in? I'm a little but confused so when is 48v always supplied if someone wanted that option. I have watched all of led gardeners videos a few times and still trying to get it to soak in. But regardless are you saying if I have 8 drivers powering 4...

Hello all, I got 4 QB288s running on on a HLG-480-48AB driver (8 boards running 4ea in total) and at the time constant voltage really appealed to me. Anyhow after getting everything setup and they all have 100k potentiometers on them. Maxed out they run so hot had to dim and on max some boards...

Hello All, I have eight meanwell HLG-480H-AB drivers that I would like to dim with the trolmaster controller....I purchased the LMA-14 lighting adapter and also the ECS-2 / RJ12 to 3.5 adapter to connect the dim leads to....I would like to splice all the driver dimming cables with wagos and...

@Bignutes gotcha will do and the light controller is dedicated to its own circuit for sure.

@1212ham yes 240, so whatcha saying ?

@TreeFarmerCharlie Square D QO double pole 80AMP says 10000AIR on it. Supposedly this high up on amperage square D QO they come in high magnetic but cannot find exact timings and stuff. Maybe over thinking this and everything will be fine. Just got a little curious this morning.

@TreeFarmerCharlie well then I should've noted that yes each set of banks with trigger cords could be set on a timer and or plugged in one at a time and should help. But still was wondering what the timing is on a breaker and how much of inrushes they can handle prior to say "no charlie no and...

@TreeFarmerCharlie I got the 12 light helios controller and on an 80amp breaker...what I'm not able to find is the inrush is a couple ms on the driver but how many ms on a breaker before it trips from an in-rush. For instance if I have 10 drivers cold starting at 350amps does the breaker support...

@Airwalker16 im going to have to agree with you as well and pretty sure the breakers can handle up to 10x inrush prior to tripping. There Is a slight delay. @Bignutes would that be required for every driver? Do you have a link to such just Incase? Thanks.

Hello all, I have a titan helios 12 light controller which is wired up to a double pole 80amp breaker and correct gauge wire. My question is I am running the kingbrite 480w which comes with the HLG-480H-48 and notes that the cold start is 35amps. When powering up say 8-10 of these...

@Greengenes707 do you splice all the driver dimming leads together using wagos and then use one ECS-2 for them all or did you get an ECS-2 for every fixture?