I wanted to share my table that I built for under $150 and it doesnt leak and you can walk on it. You can get everything at home depot except the pump and bildge drain.
itemes needed
1-8'x4' sheet of 1/2" plywood $15
5-2x4x8' $10
2-25"x96" white corrigated roofing $26
1-stick of white plastic gutter $10
2-endcaps for plastic gutter $4
1-box of 1" dry wall screws $5
1-box of 21/2" dry wall screws $5
1-400gph pump $25======== grow store
15' of 1/2" drip line tubing $10
50" of 3/16" drip line tubing$5
1-25 pack of drip line strait barbed connectors $5
1-25 pack of dripline barbed elbows $5
1-25 gallon rubbermaid resivor
1-1" bildge drain $2========grow store
1-tube of silicon
Tools needed.
drill and phillips screw driver attatchment
tape measure
pencil
circular saw or miter saw
Cut one 2x4 into two pieces 45" long
take 2 96" 2x4s and screw the 45" pieces inbetween them at each end. The overall total should be 96"x48"
Now screw the sheet of plywood to the top of the frame
take another 2x4 and cut
2 @ 21" 1@19" 1@191/2"
these are your legs the point is to have it higer in the back and have a slight slope to the side you have your rez on. so the 2 21" go on the back of the table the 19" and 191/2" go at the front where the rez is going to go and the 19 goes on the corner that the rez is on.
cut the gutter to 50" and attatch it to the front of the table drill the 1" hole for the bildge drain plug over your rez and put in the drain
take the two sheets of corigated roofing and screw them down to the table so the water flows to the gutter. make sure to have an overlap on the roofing and a 1' over hang on the gutter.
silicon all screw heads and run a bead of silcone across the bottom side of the roofing over the gutter so slow running water will not crawl back up the table and run off on the floor
your table is now done I will post pics today when my light turns on
itemes needed
1-8'x4' sheet of 1/2" plywood $15
5-2x4x8' $10
2-25"x96" white corrigated roofing $26
1-stick of white plastic gutter $10
2-endcaps for plastic gutter $4
1-box of 1" dry wall screws $5
1-box of 21/2" dry wall screws $5
1-400gph pump $25======== grow store
15' of 1/2" drip line tubing $10
50" of 3/16" drip line tubing$5
1-25 pack of drip line strait barbed connectors $5
1-25 pack of dripline barbed elbows $5
1-25 gallon rubbermaid resivor
1-1" bildge drain $2========grow store
1-tube of silicon
Tools needed.
drill and phillips screw driver attatchment
tape measure
pencil
circular saw or miter saw
Cut one 2x4 into two pieces 45" long
take 2 96" 2x4s and screw the 45" pieces inbetween them at each end. The overall total should be 96"x48"
Now screw the sheet of plywood to the top of the frame
take another 2x4 and cut
2 @ 21" 1@19" 1@191/2"
these are your legs the point is to have it higer in the back and have a slight slope to the side you have your rez on. so the 2 21" go on the back of the table the 19" and 191/2" go at the front where the rez is going to go and the 19 goes on the corner that the rez is on.
cut the gutter to 50" and attatch it to the front of the table drill the 1" hole for the bildge drain plug over your rez and put in the drain
take the two sheets of corigated roofing and screw them down to the table so the water flows to the gutter. make sure to have an overlap on the roofing and a 1' over hang on the gutter.
silicon all screw heads and run a bead of silcone across the bottom side of the roofing over the gutter so slow running water will not crawl back up the table and run off on the floor
your table is now done I will post pics today when my light turns on