Blowing warm air at girls?

2cent

2cent

Well-Known Member
I run carbon filter fan out on 8inchl1seperate
I run 6inch a1 intake base cool air.
I run 2 600w dominator cooltubes in and out on a 6inch a1. Seperate

Temp light on 20c

Is there any problem in swapping the cooltubes vent?

So disconnect my intake fan and clip up the cooltube pipe to my inrake vent
Then the extracted hot air blows backin to the tent at the base? So it pulls thru my scrog past the airpots

I pull cool air seperate but if im needing warmer can i do this? Will it affect my co2? Being as my co2 is in the downstairs room the air sucks from
 
2cent said:
I pull cool air seperate but if im needing warmer can i do this? Will it affect my co2?
Click to expand...
Instead of going through the trouble of re routing the exhaust back into the tent, why not just speed control the ventilation system so that you can keep the temps where you want them? Maybe just take the glass out of the reflectors.
 
Renfro said:
Instead of going through the trouble of re routing the exhaust back into the tent, why not just speed control the ventilation system so that you can keep the temps where you want them? Maybe just take the glass out of the reflectors.
Click to expand...
The speed controls at minimum can hear it doenstairs lol.

Plants so big man... If i remove screen am fked lol theyll fry. After heats been in the duct its cooler.
If i pop it in the tent door it warms to 24c

Feast ur eyes on the big bad beautys
 

Attachments

  • 20210123_211320.jpg
    20210123_211320.jpg
    2.2 MB · Views: 46
  • 20210123_211419.jpg
    20210123_211419.jpg
    4 MB · Views: 45
  • 20210119_223502.jpg
    20210119_223502.jpg
    3 MB · Views: 40
  • 20210106_203405.jpg
    20210106_203405.jpg
    2.1 MB · Views: 37
Well you could use an electric damper setup on a wye to divert some of the exhausted air back into the bottom of the tent based on a temperature controller.
 
Renfro said:
Well you could use an electric damper setup on a wye to divert some of the exhausted air back into the bottom of the tent based on a temperature controller.
Click to expand...
What wrong with keepong all of it?

All id hav to do is unclip the intske vent and clip it oj the open ended coolhood fan.
Turn off my intake and throw the coolhood extrac pipe in the bottom tent
 
Renfro said:
Seems like with the intake fan going there would be a positive pressure situation, not sure how effective the intake would be
Click to expand...
I mean to redundant my intake and just use the hoods fan.

Unclipp the intake fan. And put the hoods extraction in it.
My hoods intake just hangs there. I now csn hook it up to my intake room. (fresh air not loft air)

Il get a pic if poss

The top is the cooltubes.
Bottom intake from downstairs.

Disconnect intake and put hood on the room where intake was.

Then take the hoods extraction thats just blowin in the loft and throw it in the intake
Sit the intake fan in a box

20210125_023805-jpg.4806162
 

Attachments

  • 20210125_023805.jpg
    20210125_023805.jpg
    1.7 MB · Views: 67
Only problem I see is with your plants been so packed out the hot air is going to be bloing right at them/into them. You'll probably have leaves drying out. Also you'll definitely need a supply of fresh air otherwise you may run into problems. If you can have a fresh air intake and your lighting extraction mixing up in a box or something and then going out in the plantroom it may be ok.
 
TheWholeTruth said:
Not sure but is there some separate extraction to the light cooling extraction ?
Click to expand...
He mentioned an intake fan. Still it would need an exhaust hole open assuming the other recirculating system off the lights were to make for neutral pressure.
 
2cent said:
The speed controls at minimum can hear it doenstairs lol.

Plants so big man... If i remove screen am fked lol theyll fry. After heats been in the duct its cooler.
If i pop it in the tent door it warms to 24c

Feast ur eyes on the big bad beautys
Click to expand...
You can cut the screen. I had to do the same thing . Just tie them down reroute the cola sites and renet the tops of the cola and they’ll blow out again and it’ll fix ur problem. Your five weeks and a lot more plants ahead of me
 

Attachments

  • image.jpg
    image.jpg
    1.9 MB · Views: 6
  • image.jpg
    image.jpg
    1.6 MB · Views: 6
As i said l lol
I have seperate 8inch carbon scrubber to outside
1000cmf
.
Wheb i put it in as a test i get maxxx 23c man.

The hood runs into the loft along 3meters and back in
Airmovement and distancr cools it down. Theres no frying

Simply wanted it to be pulling my fresh air past the lights before entering tent.

Then carbon does heat removal same as if it was open bulbs

Right now i have 3 fans
Carbon fan to outside.
Hoods fan. In from loft out in loft
Intske fan in from room below.

I simpley want to swap
Carbon filter to outside
Intake room to hoods and into tent(not just in loft)

No intake fan as hoods runs from my fresh room warms it and passes it in the tent


So the hoods is now intske just warms air. After cooling it on the run out before throwijg it in.

Raises temps from 20 to 23c max.
 
You must log in or register to reply here.

Similar threads

BB Boomer
Drying Tent Air Exchange While Using AC
Replies
11
Views
791
MissinThe90’sStrains
MissinThe90’sStrains
N
Efficiency please!
Replies
7
Views
647
Mumbeltypeg
Mumbeltypeg
R
Will there be too much heat ???
Replies
4
Views
487
coreywebster
coreywebster
S
HVAC question
Replies
2
Views
273
Samwiseman420
S
D
Running exhaust fan 27/7 vs intermittently
Replies
17
Views
1K
ProPheT 216
ProPheT 216
Back
Top