DIY with Quantum Boards

Benefit14snake · Jun 17, 2017

ttystikk said:
With the appropriate heat sink these boards can take well over 100W. You can get most of the way there by aiming a fan at the board for cooling.

3 amps is the recommended maximum, I understand.

So they should be able to do just over 160w per board but that seems pretty high.

GardenGuy · Jun 17, 2017

the context of the question is about managing 1 board with the minimum wattage needed, with different sized plants and different needs. Slate 2 here.

HydoDan · Jun 17, 2017

GardenGuy said:
qb288 @ 25w 20" from the seedlings and they stretched a bit. To prevent the stretch should i lower the panel or bump the amp to 50w or something? I'd prefer to bump the amp cause next to the seedlings there is a mother plant. noob.

Turn that light up to 50 watts and see.. Once the plants adapt go all the way..

GardenGuy · Jun 17, 2017

Thanks @HydoDan! did it. for my veg, all the way means 117w. I'll keep on monitoring them.

Moflow · Jun 17, 2017

ttystikk said:
With the appropriate heat sink these boards can take well over 100W. You can get most of the way there by aiming a fan at the board for cooling.

150 wall watts for me, full wack!

Moflow · Jun 17, 2017

GardenGuy said:
the context of the question is about managing 1 board with the minimum wattage needed, with different sized plants and different needs. Slate 2 here.

Yea, I got slate 2 @ 150 watts

Evil-Mobo · Jun 17, 2017

GardenGuy said:
qb288 @ 25w 20" from the seedlings and they stretched a bit. To prevent the stretch should i lower the panel or bump the amp to 50w or something? I'd prefer to bump the amp cause next to the seedlings there is a mother plant. noob.

I would do both don't worry about the stretch so much when you up pot it you can bury the stem to the point of your liking

drgroove · Jun 17, 2017

Thanks guys !

GardenGuy · Jun 17, 2017

I assume that this could cause stem rot or something like that. Does the cannabis main stem act like the tomato does with short and fat stem roots? Hope i'm understandable.

RandomHero8913 · Jun 17, 2017

GardenGuy said:
I assume that this could cause stem rot or something like that. Does the cannabis main stem act like the tomato does with short and fat stem roots? Hope i'm understandable.

Yeah, you can bury a cannabis plant in the ground much like a tomato plant. Roots will eventually grow out of the stem.

Balko186 · Jun 17, 2017

Can I run a kit without measuring watts or must I be able to measure? I own a 260w kit and haven't used yet

Stephenj37826 · Jun 17, 2017

Balko186 said:
Can I run a kit without measuring watts or must I be able to measure? I own a 260w kit and haven't used yet

You don't have to measure watts.

Budzbuddha · Jun 17, 2017

Balko186 said:
Can I run a kit without measuring watts or must I be able to measure? I own a 260w kit and haven't used yet

No reason to measure ... The kit was built around the specs setup by @robincnn and @Stephenj37826 ... Just put it together and enjoy.

It REALLY IS that simple.

Budzbuddha · Jun 17, 2017

Thought all of you would get a laugh out of these , I seen on the web.
Unknown source ..... Probably made in some shack outside of Shanghai.

Looks like a shitload of B Stock epistar LEDs ...... And scotch tape.

714steadyeddie · Jun 17, 2017

The girls are all adjusted to the new light

I'm at 18ins away

Evil-Mobo · Jun 17, 2017

I'm finding depending on strain 18-24" to work very well

GardenGuy · Jun 18, 2017

Seedlings where over 1ft from the qb@25w and stretched. Bumped the board to 55w and stretched from 1" to a bit 1.5" overnight. Now i got them to 8" from the board still @55w under not exactly direct light, but close enough. Let's see...

edit: got them 5-6" under the board with the clones @75w.

PSUAGRO. · Jun 18, 2017

Budzbuddha said:
Thought all of you would get a laugh out of these , I seen on the web.
Unknown source ..... Probably made in some shack outside of Shanghai.

Looks like a shitload of B Stock epistar LEDs ...... And scotch tape.

View attachment 3962927

I remember these guys, first to put green diodes in their "spec blend"=====blast from the past

Balko186 · Jun 18, 2017

Budzbuddha said:
No reason to measure ... The kit was built around the specs setup by @robincnn and @Stephenj37826 ... Just put it together and enjoy.

It REALLY IS that simple.

shouldn't worry about dimming or increasing much or just estimate?

Stephenj37826 · Jun 18, 2017

Balko186 said:
shouldn't worry about dimming or increasing much or just estimate?

If you use B type driver and the potentiometer we have on the site it has a 50% "click".

DIY with Quantum Boards

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member