doublejj's next big adventure....Lone Oak Farms 2016

757growin · Jul 19, 2016

doublejj said:
bought these low temp plates....

You should build a couple of them and sell them at the fall bbq. If it's running right I'd buy one!

eddy600 · Jul 19, 2016

Was at the green Dragon collective looking for a few clones half the people wore buying that type of stuff it's looks like a good investment to me.good luck with that

doublejj · Jul 19, 2016

Well it only took me several trips to the hdrw store but I finally managed to get the press converted to 20ton air jack. I bought a long hose so I can leave the compressor outside while we are squishing rosin...
also picked-up a small chest freezer for pre-freezing trim before tumbling..and a marble tile for cooling rosin

Vnsmkr · Jul 19, 2016

Thats exactly what I would have done but I may have gone 1 step further and tapped a hole in the wall from outside for permanent air hose fitting.

Looks good

doublejj · Jul 19, 2016

Vnsmkr said:
Thats exactly what I would have done but I may have gone 1 step further and tapped a hole in the wall from outside for permanent air hose fitting.

Looks good

I have been thinking I could drill a hole in the floor in the corner & drop the hose down into the basement & put the compressor down there...

Mohican · Jul 19, 2016

Way better than my two clothes irons on 2x4s and a hinge!

Get fine mesh SS screen tubes for your pressing filter!

doublejj · Jul 19, 2016

everything you need to make 2 kief tumblers....

Vnsmkr · Jul 19, 2016

doublejj said:
I have been thinking I could drill a hole in the floor in the corner & drop the hose down into the basement & put the compressor down there...

Even better

doublejj · Jul 19, 2016

I pimped out my air jack with a plastic handle over the release valve for ez operation. I won't have to use that slotted rod to release the jack pressure...

Smidge34 · Jul 20, 2016

This is better than watching DIY Network lol! The Bob Villa of cannabis! :clap:

Grandpapy · Jul 20, 2016

Im surprised it's plates and not rollers, Oh, the possibilities that come from demand.

LockedOutOfHeaven · Jul 20, 2016

doublejj said:
Ordered SS screen to build 2 new kief tumblers. Everything else I can get at Home Depot...
View attachment 3733914

Love it! What kind of motor is that?

Vnsmkr · Jul 20, 2016

LockedOutOfHeaven said:
Love it! What kind of motor is that?

rotiserrie for a bbq

beachball · Jul 21, 2016

mushroom head said:
Check out solventlessmind on instagram. He's a beast at pressing.. View attachment 3736242

The artful squisher. Very, very nice :clap:

doublejj · Jul 21, 2016

Sorry I haven't been out to the farm for over a week so I don't have any updates. I have been working on my rosin press set-up. But I will get out there soon....

penguinking · Jul 21, 2016

damn jj... looks like the garden is on smash mode! good clean work. I just looked through this entire thread. inspirational.

doublejj · Jul 21, 2016

I have made a little progress on the kief tumblers. I hope to have them finished today..

doublejj · Jul 21, 2016

Got first tumbler finished & ready for trim....time to finish #2

Vnsmkr · Jul 21, 2016

Did you cut the bucket in 1/2 and then put back together or you just cut a window for the silk screen?

757growin · Jul 21, 2016

doublejj said:
Got first tumbler finished & ready for trim....time to finish #2
View attachment 3738104

I got fresh trim if you need some practice material ;-)

doublejj's next big adventure....Lone Oak Farms 2016

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member