SnapsProvolone
Well-Known Member
The smallest batch I've made was 5 grams bho. Too much loss stuck to the mixing vessel to justify many smaller runs.
E-Juice/Flavor ratio
- Thread starter hoova
- Start date
hoova
Member
but it doesn't just pour out like reg ejuice. all the residue and sticky stuff is on the wall of the tank stillJust wipe the tank out with a paper towel and change the coil. Nothing fancy. Nautilus and iClear 30. A bigger tank is handy if the battery matches it and you have a group.
hoova
Member
I have an eleaf istick. would this screw into it? (I'm not home so I can't see)
jondamon
Well-Known Member
I personally haven't tried EJMIX simply because you can't get it in the UK.
I use PG or PEG400.
When I made a QWISO run last time from 10g of buds I got back 1.5g of oil.
I decarbed the oil in a warm oil bath in a little pyrex dish then added my PG into it.
I continued to heat until the PG was mixed with the QWISO.
This was before Xmas and my PG/QWISO solution is still in solution and hasn't seperated about 4 weeks or more since being made.
A lot of the MMJ prefilled cartridges are using PEG400 from my understanding.
J
jondamon
Well-Known Member
I currently use an iTaste MVPv2 with Kangertech Mini Protank3 for vaping my THC juices.
When cleaning I break it all down and rinse under a tap. Any residuals that won't clean I use ISO to clean them. To be honest though i haven't cleaned out my Mini protank3 since before I made my QWISO THC juice.
I like vaping my THC eJuice in my mini pro3 at around 3.8v with around 8w on a 1.8ohm dual coil.
I use an Aspire Nautilus BVC for my every day vaping gear at 3.9v and 7.5w.
J
When cleaning I break it all down and rinse under a tap. Any residuals that won't clean I use ISO to clean them. To be honest though i haven't cleaned out my Mini protank3 since before I made my QWISO THC juice.
I like vaping my THC eJuice in my mini pro3 at around 3.8v with around 8w on a 1.8ohm dual coil.
I use an Aspire Nautilus BVC for my every day vaping gear at 3.9v and 7.5w.
J
jondamon
Well-Known Member
I've always stayed away from ethanol based flavours.
I have a lemon ethanol based flavour that I havent even tried yet in VAPE juice.
Realistically though ethanol flavouring should be ok but a lot of people say you can taste that it's alcohol based and it provides more throat hit (another reason why people add grain alcohol or vodka to VG only vape juices).
From my understanding it's certain oil based flavourings that you have to be careful of when mixing into vape juices.
J
GrowinDad
Well-Known Member
Most flavors will be in an ethanol solution. Oils are more used for things like capsicum oils, spicy heat. I would think anything oil based would be a problem. Ethanol is fine,
And once again for anyone looking to keep ejuice in solution without using a ton of EJ Mix. I have gone as low as one drop of EJ Mix per ML of QWET, mixed it in well, and then added PG and it stays in solution.
And once again for anyone looking to keep ejuice in solution without using a ton of EJ Mix. I have gone as low as one drop of EJ Mix per ML of QWET, mixed it in well, and then added PG and it stays in solution.
hoova
Member
what type of tank do you use to vape your thc juice? do you use flavoring? if so, what kind and how many drops?
jondamon
Well-Known Member
A lot of the flavours in the UK are based in MPG mono propylene glycol.
Some are in ethanol.
Anything based in or with oil should be avoided at all costs for vaping.
J
SnapsProvolone
Well-Known Member
Too thick and it won't flow through the wick and you risk burning out dry coils.
jondamon
Well-Known Member
Yes too thick.
But also PG doesn't produce big clouds.
The PEG series allows a bit more cloud but that's what VG helps to add to normal vape juice is more cloud and some sweetness but obviously VG causes separation in THC juice.
J
GrowinDad
Well-Known Member
Who cares about cloud? If I am vaping my weed juice, I would prefer it not to cloud too much.
My EJ Mix was lightly flavors with some soft notes by a friend who makes nic juices. We were just trying mask the EJ Mix flavor. Now that I only use 1 drop of it per ml of oil, it really has no impact.
If your juice is too thick, then add more mix.
My EJ Mix was lightly flavors with some soft notes by a friend who makes nic juices. We were just trying mask the EJ Mix flavor. Now that I only use 1 drop of it per ml of oil, it really has no impact.
If your juice is too thick, then add more mix.
hoova
Member
So, i just made my best batch yet. I took 3ml of EJ-Mix. put it into a shotglass. set the shotglass in a pan of water (double boiler style) got the temp up to like 120. added 230mg wax and mixed real good. then added 3 drop of Bavarian Cream, 2 drops of Vanilla Custard and one drop of strawberry banana