My first whole room SCRoG
- Thread starter jondamon
- Start date
jondamon
Well-Known Member
Day 67 of 12/12.
EC of res 0.6-0.7 flashing between the 2.
I have increased irrigation to x5 to achieve more runoff per 24 hours
I am now also feeding 2x during the 12 hour dark as this is helping to stabilise the runoff and they’re drinking it, as temps are higher right now in the U.K. and my intake air temp is warmer than normal (it’s the U.K. after all lol) and I don’t run an AC.
@Star Dog @myke
my 8LPH PC emitters have arrived today.
I’m expecting the valve T and the valve to arrive tomorrow.
I won’t be adding anything to the system until this flowering is finished so that I can clean and flush the system and make alterations without being live.
I’m also considering making myself a water level indicator for the tote (if I can buy the parts cheaper than the £8.95. DWC bucket kit)
EC of res 0.6-0.7 flashing between the 2.
I have increased irrigation to x5 to achieve more runoff per 24 hours
I am now also feeding 2x during the 12 hour dark as this is helping to stabilise the runoff and they’re drinking it, as temps are higher right now in the U.K. and my intake air temp is warmer than normal (it’s the U.K. after all lol) and I don’t run an AC.
@Star Dog @myke
my 8LPH PC emitters have arrived today.
I’m expecting the valve T and the valve to arrive tomorrow.
I won’t be adding anything to the system until this flowering is finished so that I can clean and flush the system and make alterations without being live.
I’m also considering making myself a water level indicator for the tote (if I can buy the parts cheaper than the £8.95. DWC bucket kit)
jondamon
Well-Known Member
Ok so after extensive searching I couldn’t find the parts for less than this kit cost £8.95.
Now obviously if I was buying parts in bulk and fitting these together as a kit then I would have the ability to make these for under £9 each but buying single items.
no way I could do it.
Little plug for the company too lol.
Now obviously if I was buying parts in bulk and fitting these together as a kit then I would have the ability to make these for under £9 each but buying single items.
no way I could do it.
Little plug for the company too lol.
myke
Well-Known Member
Sure helps things go easier from mixing to draining and aerating.Total control for just a few $'s
jondamon
Well-Known Member
I’ve got the bypass around 1/3 closed 2/3 open.
I started with everything open and the pump on full (figured it’s designed to run best on fully open flow)
nothing came out of the drippers.
So I opened the drippers to make sure it wasn’t a flow issue with them and they were open and no flow.
I then began to close the bypass valve slowly and then flow began coming out of the drippers too quickly as i know the drip rate now lol.
So I left the bypass where it was and reduced the flow on the drippers to where I needed it.
If you look At the running pic you can see the valve is just slightly off centre.
It’s perfect.
Next, water level indicator that should be here tomorrow but I won’t be fitting that until the res is empty lol.
jondamon
Well-Known Member
If not I’ll know tomorrow lol. It’s nearly 1am and the Mrs is in bed lol.
I ain’t going back in now lol.
It did cycle it on and off a few time in those 5mins I didn’t just run it fully for 5mins.
jondamon
Well-Known Member
It’s getting serious now lol.
Diamond tipped universal 25mm hole saw lol.
I’m planning on removing the tote tonight as it’s almost empty and refilling once I’ve added this water level kit into the tote!
When I do refill I will be refilling with 0.6EC of just my base bloom A/B to get to the end of the grow.
Diamond tipped universal 25mm hole saw lol.
I’m planning on removing the tote tonight as it’s almost empty and refilling once I’ve added this water level kit into the tote!
When I do refill I will be refilling with 0.6EC of just my base bloom A/B to get to the end of the grow.
jondamon
Well-Known Member
jondamon
Well-Known Member
It was a case of beggars can’t be choosers and picked up something at work that would do rather than pay for something I’ll never use again until I need a new tote lol.
jondamon
Well-Known Member
Installation.
Nice and simple once the tote was empty and cleaned.
I drilled the hole slowly to Stay on course.
cleaned up the hole using sand paper to remove any of the final edges.
cleaned the whole tote again.
dried the tote where the kit was going and fitted it.
rubber seal on each side of the tote.
tested for 30mins and no leaks.
Nice and simple once the tote was empty and cleaned.
I drilled the hole slowly to Stay on course.
cleaned up the hole using sand paper to remove any of the final edges.
cleaned the whole tote again.
dried the tote where the kit was going and fitted it.
rubber seal on each side of the tote.
tested for 30mins and no leaks.
jondamon
Well-Known Member
Cheers bud. Much appreciated.
Just for this grow alone ive created these threads for anyone else who may want to setup similar.
DIY drip system DTW
Evening all. I wanted to share a DIY drip feed DTW system I’ve built with some help from others on RIU. Namely @myke. I built this system to water 2 plants in 18L pots of 100% coco as many times I needed on a 15 minute segmental timer. let’s go over some parts. SUPPLY + DELIVERY RING...
rollitup.org
DIY SCROG BUILD
Good evening everyone. Just thought I would post this thread as I’ve ordered parts to build myself a scrog screen for my area. parts list all from eBay 6x1m lengths of 20mm tubular conduit 4x 3way connectors 20mm £6 delivered 1m x 1m with 2” squares ready made scrog net £6 delivered...
rollitup.org
