ismokealotofpot
New Member
I found this Or you can buy the stuff witch would be way easier.[h=3]How to make your own Silver Colloid Generator.While it has been discovered that 30 volts is the ideal forSilver Colloid production, 27 volts is very effective andhappens to be the convenient result of wiring three 9-voltbatteries together.Therefore,you'll need three 9-volt transistor radio batteries, three battery snap-on lead connectors, 2 insulated alligator clips, 1 "grain-of-wheat" 24 volt 40 mA sub miniature incandescent bulb, a foot of 3/32" heat-shrink insulation tubing, a foot of 2-conductor stranded insulated wire for clip-leads, a small box to put it all in, and 10" of pure silver wire (.999 fine).This should cost under $30.00 for everything. Assuming someskill with a soldering iron, you should spend about thirtyminutes constructing the generator.Solder your three snap-on battery clips in series (red toblack) to provide 27 volts. Connect a 24V incandescent lampin series with either positive or negative output lead.Solder the red insulated alligator clip to the positive (anode)and the black insulated clip to the negative (cathode)2-conductor lead wires. Insulation is shrunk over solderedconnections using a heat gun or hair dryer.Cut your 10" of silver wire in half. Bend top ends of yourtwo 5" silver electrode wires so they can clip over the top rimof a plastic or glass cup (not metal).About 4" of each wire should be submerged.WARNING! Use ONLY pure silver (.999 fine) electrodes. #14 gaugeis the preferred thickness. Pure silver is sometimes availableat electroplating supply companies. Or, inquire at a jewelrystore specializing in silver about who their wholesale supplieris.Do not use sterling silver (.9275) since sterling containscopper and nickel.NICKEL CAN BE TOXIC. (With this in mind, you may want to havea chemical analysis (assay) of your purchased silver in additionto the written word of your supplier.)If the Silver Colloid is to be ingested or injected, be sure touse distilled water. Tap water is fine for other uses, such asfor a topical spray or for plants. Also, before beginning tomake your Colloidal Silver you will need to make a salinesolution for enhancing conductivity.**************************************************NOTE: Two points of interest since this file was posted; 1) DO NOT USE SALT - just use distilled water 2) An ingot of silver cut in half works better than wire**************************************************Saline solution can be made by mixing six ounces of distilledwater with one tea-spoon of sea salt in a separate container.Do not use common table salt as table salt has chemicaladditives. After stirring the salt solution, pour some of thewater into an eye dropper bottle.Now you're ready to make Colloidal Silver. Pour eight ouncesof water into your glass. Add 1 or 2 drops of saline solution(3 drops at the most; if you use too much salt, you'll bemaking silver chloride instead!) to distilled water and stirwith a plastic/non-conductive utensil.Insert silver electrode wires. Placement of wires is not critical,but they must not be touching each other or the process willstop. (You cannot shock yourself in this process so do not beconcerned.)Attach alligator clips to the ends of the silver electrodewires coming over the outside rim of the glass and you willsee a grey mist inside the glass start to peel away from thepositive polarity wire while bubbles of hydrogen rise fromthe other.Laboratory tests show that this method creates a silver colloidof approximately 1 ppm per minute of activation time.Since you are only taking microscopic particles from the silverwire, your silver wire may very well last for years.The brightness of the light bulb is related to the conductivityof the water. It is not necessarily a problem if the bulb isvery dim or even remains dark as long as the process itself isoccurring. (If the bulb is dark you can always consider addingone more drop of saline solution next time.) Do not add salinesolution after process has begun.Of course, when batteries are old, the light will also becomedimmer, signaling it's time for a change. Touch the two alligatorclips together to test the brightness of the bulb as a batterycheck. A fresh set of three alkaline batteries should makeseveral hundred thousand batches of concentrated Silver Colloid.Also, put a few drops of Silver Colloid in the saline solutionto prevent fungus growth.When finished, detach alligator clips. Clean silver electrodewire after each use to remove dark oxide on the anode. Use asmall piece of 1/4" thick nylon kitchen scouring pad to polishdried silver, then wipe with paper napkin to make ready fornext use.Store your Colloidal Silver in dark, non-conductive (and ifplastic, non-reactive) containers, like empty hydrogen peroxidebottles. Keep away from light as even room light will degradecolloids rapidly by turning solution grey or black just asexposure to light darkens the silver in camera film. Stirthoroughly or shake each time before using. Keep cool, but donot refrigerate.In using your own home-made silver colloid generator it willbecome apparent that you now have the power to safely protectyourself, your family, your pets and plants, your community,and (through the dissemination of this information), our nation,from over 650 pathogens, viruses, microbes, fungi and parasites.Upon creating your first batch of Colloidal Silver, you willfind it tastes the same as untreated water. And it won't sting,even in a baby's eyes.Congratulations and bon appetit![/h]