post your smoking utensil

M

MisterNiceGuy

Well-Known Member
i think this isn't the first time this has happened. this forum is plagued with stoners. you expected something else to happen???
 
M

MisterNiceGuy

Well-Known Member
ah, all you have to do is pull out the Serian Crystal from slot 7-B and place it in slot 4-B, will reset configurations and wallah. On Line Again
 
T

thephantompain1990

Well-Known Member
N3wm4n said:
Heres Jerome made by Jerome Baker with an illidelp ash catch supposedly quite rare
Click to expand...
you have a video on youtube?

your bong is really nice...the a/c convinced me i wanted an illy(too poor right now but later on)

K1ng j.AK said:
hahaha. my friend back in the day had a naked chick pipe. you hit out the V and load the mouth, shit was hilarious. never seen one since..
Click to expand...
gorilla glass has it...just go down the page a little bit

http://www.gorillaglass.com/acrylics.htm
 
Gryphonn

Gryphonn

Well-Known Member
Ok, time to get back on track. Geez folks, all these flash smoking implements make me jealous. I once had a four stage glass bong....back in the 80's. Someone jumped on it. My last stoneware bong, bought before these stupid implement selling laws came into Australia, got smashed by a psychotic cat.

Nowadays we just keep our stem and cone piece and make our own.

The Ice-Break Bottle Bong

The bottle is made from Coffee coloured HDPE plastic. When heated, it softens, but doesn't warp or go brittle. We make a small hole 1/8 inch or 4mm in the side with a knife tip, using a drilling action. Then we warm the stem and apply a flame to the hole in the HDPE bottle, just enough to soften the plastic a little. The stem is then forced into the softened hole. If you get it right, you'll get a perfect seal and won't have to resort to 'Blu-tac' or some other sealer. You can get Ice-Break bottles over here in 500ml, 750ml (pictured), 1 litre, and 2 litre square HDPE bottles.

Using Fine Mesh as a Filter

The mesh in the cone piece gets loaded with weed. It filters the ash and prevents 'pull-through'. All the weed burns instead of getting sucked through the conepiece hole. It takes a little getting used to, but works a treat. Also, if you use a dedicated ash-tray and flick the ash from the mesh into that, you catch anything that might remain around the edge of the mesh. In desperate times you can use a tea strainer to shake the ash and collect any unburnt bud. If you're going to try this, get the finest mesh you can and grind your weed really fine as well.

Disposable and Easy to Replace

The beauty with this set-up is that these bottles are easy to clean or dispose of, and so long as you have your stem and cone-piece, you'll be able to find an Ice Break bottle anywhere you can find coca-cola in Australia. Of course, you can use other plastics, I prefer this type though. Back in the 70's and 80's 'Orchy' bottle bongs were the standard throw together bong in Australia.

Specifications

For an idea of size, that stem is about 5 inches, or 12cm long with a 1/2 inch (15mm) diameter. The hole in the brass cone piece that holds the mesh has been reamed out to 1/8 inch diameter (about 2 or 3mm) to allow for better airflow through the mesh.

Smoking

The feeling of pulling through this bong is different than when pulling without the mesh. There is no 'pull-through' or 'shotgun' feel as the bud pops through the cone hole. It is a long smooth pull with a little more air mixed in the smoke than usual. We have a 1/4 inch (5mm) shotgun hole at the back of the bong. Even though the conepiece is small, it takes a big pull to toke it all up.

bongsmilie

[That was chapter two, from the 'Smokers Guide For Povvo's] :roll:

 
You must log in or register to reply here.
Top