DIY with Quantum Boards

2

2com

Well-Known Member
Would an hlg-320h-54 have what it takes to run four qb288 v2 rspec in parallel?

And what about four qb96?

edit: sp.
 
pop22

pop22

Well-Known Member
Finally going to have a real grow under my Diablo light. Three Blackberry Gum will be the main grow, with 40 Blue Dragon temporarily residing with them. The CBD Kush in the back should be done in about 30 days. Dragons will go to the tent with the Gorilla Glue in it now when they finish, or I might have to shuffle some to my small tent, we'll see!

Bleckberry gum and blue dragons pic1 -11-18-2020.jpg
 
Sade

Sade

Well-Known Member
Yodaweed said:
Bro all you new guys on this site do is make outrageous claims with nothing to back it up, you make these dumb charts up that mean nothing. Those lights are junk PCB board lights, oldest LED grow light tech on the market, if you want to see those things smashed up go watch @REALSTYLES break his mars hydro LED, that's the tech those lights use. Junk PCB board tech.
Click to expand...
dude probably has his foot in his mouth these days. However I actually hope these have swayed his opinion.
 
Frank Nitty

Frank Nitty

Well-Known Member
DAMMIT MAN!!! THIS IS THE SECOND LIGHT THAT I BOUGHT FROM HLG THAT HAS FALLEN APART ON ME!!! HOW CAN I GET IT REPLACED IF STEPHEN IS NOT AROUND ANYMORE??? OR IS HE??? I DON'T KNOW WHAT IS GOING ON HERE IN THIS THREAD CAUSE I STOPPED GROWING FOR A LITTLE BIT AND WHEN I CAME BACK I JUST CATCH BITS AND PIECES OF WHAT HAPPENED, AND I STILL DON'T UNDERSTAND...
 
farmingfisherman

farmingfisherman

Well-Known Member
Frank Nitty said:
DAMMIT MAN!!! THIS IS THE SECOND LIGHT THAT I BOUGHT FROM HLG THAT HAS FALLEN APART ON ME!!! HOW CAN I GET IT REPLACED IF STEPHEN IS NOT AROUND ANYMORE??? OR IS HE??? I DON'T KNOW WHAT IS GOING ON HERE IN THIS THREAD CAUSE I STOPPED GROWING FOR A LITTLE BIT AND WHEN I CAME BACK I JUST CATCH BITS AND PIECES OF WHAT HAPPENED, AND I STILL DON'T UNDERSTAND...
Click to expand...
What fell apart on your light? Was it a DIY or a prebuilt? Never heard of one falling apart before??
 
Doug Dawson

Doug Dawson

Well-Known Member
Frank Nitty said:
DAMMIT MAN!!! THIS IS THE SECOND LIGHT THAT I BOUGHT FROM HLG THAT HAS FALLEN APART ON ME!!! HOW CAN I GET IT REPLACED IF STEPHEN IS NOT AROUND ANYMORE??? OR IS HE??? I DON'T KNOW WHAT IS GOING ON HERE IN THIS THREAD CAUSE I STOPPED GROWING FOR A LITTLE BIT AND WHEN I CAME BACK I JUST CATCH BITS AND PIECES OF WHAT HAPPENED, AND I STILL DON'T UNDERSTAND...
Click to expand...
I too am curious about what fell apart, the all caps doesn't help explain it. Have you called HLG? What came apart? Yes @Stephenj37826 is still around. Perhaps you can expand on what you are talking about such as age, model and what came apart I am sure HLG, known for their great customer service, will be around to respond.
 
Frank Nitty

Frank Nitty

Well-Known Member
Doug Dawson said:
I too am curious about what fell apart, the all caps doesn't help explain it. Have you called HLG? What came apart? Yes @Stephenj37826 is still around. Perhaps you can expand on what you are talking about such as age, model and what came apart I am sure HLG, known for their great customer service, will be around to respond.
Click to expand...
All caps wasn't a big deal, sometimes I just do it... I bought a 240w kit last year and when I put the wire from my driver to the connector the connector came off... I am no good at soldering anything so that's out of the question for me and I can't afford to buy another light... I know they would fix it,l was just wondering where @Stephenj37826 was since I never cee him commenting
 
Doug Dawson

Doug Dawson

Well-Known Member
Frank Nitty said:
All caps wasn't a big deal, sometimes I just do it... I bought a 240w kit last year and when I put the wire from my driver to the connector the connector came off... I am no good at soldering anything so that's out of the question for me and I can't afford to buy another light... I know they would fix it,l was just wondering where @Stephenj37826 was since I never cee him commenting
Click to expand...
Ok, just seemed like you were mad, no big deal. So you purchased this last year as a diy, the connector came off and you still have it? I am sure they would have just sent you another had you contacted them. If it were me I would just call HLG and I am sure they can help you, well maybe, not sure after waiting a year what they will do. Worst case scenario take it to any electronics store where they do repair, a 5 min solder job will cost next to nothing. Good luck bud, no matter what you should get it replaced or repaired. It seems like a sin to have such a great light sitting in a box.
 
farmingfisherman

farmingfisherman

Well-Known Member
Doug Dawson said:
Ok, just seemed like you were mad, no big deal. So you purchased this last year as a diy, the connector came off and you still have it? I am sure they would have just sent you another had you contacted them. If it were me I would just call HLG and I am sure they can help you, well maybe, not sure after waiting a year what they will do. Worst case scenario take it to any electronics store where they do repair, a 5 min solder job will cost next to nothing. Good luck bud, no matter what you should get it replaced or repaired. It seems like a sin to have such a great light sitting in a box.
Click to expand...
How about taking a photo of what fell off? This sounds pretty simple to fix, I'm sure it's a really thing to resolve.
 
ilovereggae

ilovereggae

Well-Known Member
PadawanWarrior said:
They don't JUST fall off. You had to have hit it or something, lol.
Click to expand...
to be fair, those molex connectors are easy as shit to break. ive snapped a few of the covers off trying to remove wires. I had to use tweezers to get the wires out. still work fine i just had to cover the tops w electrical tape. its not hlgs fault, they are an industry standard connector and i'd much rather use those than solder my own. you definitely gotta take your time with them though. seems like there's a multi million dollar business in making a better version.
 
PadawanWarrior

PadawanWarrior

Well-Known Member
ilovereggae said:
to be fair, those molex connectors are easy as shit to break. ive snapped a few of the covers off trying to remove wires. I had to use tweezers to get the wires out. still work fine i just had to cover the tops w electrical tape. its not hlgs fault, they are an industry standard connector and i'd much rather use those than solder my own. you definitely gotta take your time with them though. seems like there's a multi million dollar business in making a better version.
Click to expand...
I thought he was talking about a connector on the board, not the Molex connectors.
 
You must log in or register to reply here.
Top