BHO with Vacuum oil/wax tutorial

[650baquet]

can you please explain wtf "650baquet" means? I tried to figure it out. Stumped.

Guzias1 was a random ass name I used a while back ..

haha i owned a Kawi Ninja 650R 4yrs ago...that's the 650...and baquet is actually Baquet, my last name...pronounced like banquet only without the "n"

there ya go! i've been using that for pretty much everything a long time now..

in regards to my distiller...the pressure cooker has a safety pressure check deal that is suppose to pop up under pressure and prevent you from being able to open the lid. Well it's an issue because i couldn't figure out a was to either plug the hole or manually lift the pin so it is sealed under 0 pressure right from the beginning.

I know older pressure cookers don't have this feature so i'm going to look for one...or honestly just use a regular pot, drill a hole and attack a fitting for the copper tubing just like Fadedawg did with the asparagus steamer. I am just curious what he used for the seal.

Yesterday after returning the pressure cooker i spent some time looking at random pots trying to match up a replacement seal for a pressure cooker that had the same diameter and none of them fit well enough.

That's my goal this morning...finish distiller and test by the end of the day...even if it's with water. Before i run around looking for that stuff i'm going to start a butane soak with a decent amount of sugar leaf that i've picked off my bud before i smoke or vape it. Including some stems, not really going for the most pristine oil just want to get everything i can then i'll winterize it.

 

[Guzias1]

My goal this morning, stop thinking about food while trapped in the mountains :[[
sooo, i snapped some pics of my ladies, growing weed is funnnnnnnnnnnnnnnnnnnnnnnnnnnnn.

also, this isnt good, i packed my tube inconsistently, which led to frozen pockets, which led to lack of butane pressure exiting my tube..
equaling a pretty cool pick, but dang! i ended up using a dabber tool to collect oil tear drops, and re ran the material towards the end of this tube(winterizing that one)
this one be for the wax!

 

[Guzias1]

Yesterday after returning the pressure cooker i spent some time looking at random pots trying to match up a replacement seal for a pressure cooker that had the same diameter and none of them fit well enough.

That's my goal this morning...finish distiller and test by the end of the day...even if it's with water. Before i run around looking for that stuff i'm going to start a butane soak with a decent amount of sugar leaf that i've picked off my bud before i smoke or vape it. Including some stems, not really going for the most pristine oil just want to get everything i can then i'll winterize it.

well, way to not jack up the new pressure cooker. did the people a the store look at you funny when you bought it? then relieved once you returned it ?

hope you make some good progress today, post how to's, and what not, once you got this nailed ! :]

 

[650baquet]

well, way to not jack up the new pressure cooker. did the people a the store look at you funny when you bought it? then relieved once you returned it ?

hope you make some good progress today, post how to's, and what not, once you got this nailed ! :]

Lol no funny looks from the ppl at Ace no. I'm not finding shit at second hand stores here so looks like I'm gonna have to spend more than I want to. I'm considering using two SS dishes top to top with a seal between them but I'm still looking for a good pot to use second hand. Honestly my biggest issue is finding a seal for some reason. Wonder if I can find a square of seal that I can cur to fit whatever pot I find. Keep you posted while I shop around

 

[Guzias1]

Lol no funny looks from the ppl at Ace no. I'm not finding shit at second hand stores here so looks like I'm gonna have to spend more than I want to. I'm considering using two SS dishes top to top with a seal between them but I'm still looking for a good pot to use second hand. Honestly my biggest issue is finding a seal for some reason. Wonder if I can find a square of seal that I can cur to fit whatever pot I find. Keep you posted while I shop around

yuppp. thats where i got stumped on trying to come up with my vacuum chamber. it doesnt need to be too sealed though correct? just enough so vapors dont escape..

how about some sort of rubber material(shower curtain? something in the nature..), and clamp your too SS bowls together, to make a tight seal?

dont give up! would love to hear you come up with a good cheap idea :]

 

[Guzias1]

its friday guyss. im feaking bored at work!
its hot as hell,
my truck is in the shop.
my freezer has a batch of winter ready to go.
my vacuum chamber has been in full use for the last 3 weeks!
i still have 6oz of my latest harvest to blow!
i need butane!
i have no truck! i need to pickup some master cases..
its friday!
smoke.. ... that sucked, i only have shitty weed at work :[
goddd, that was soo gross, that weed was sitting on my dash board for who knows how long.. sun and air = SUPER HARSH/DRY WEED, did you guys know this yet? like i said, im bored as shit..

I may go smoke some of my bosses. his weed aint too hot either though, grrr..

where was I?

ooo, so, i need butane! lowest price ive picked up a master case for is 230( locally).. i called up a place about 3 hrs round trip away.. i can get two for 350 total.. so.. is it worth the drive? yes, will i drive there by tomorrow am? if i have my truck, yes!!

god, i have to scrape my dish today! have i ever mentioned how exciting that is? lolll. soo lame, people and their scrape videos.. loll, i have some lame videos too, who am i kidding..

cmon new people! jump on the thread, show us up! :]

650 banquet makes sensi finally!

saying your last name is sooo freakin weird though..

 

[Guzias1]

thread is dead, should be deleted :[

 

[vacpurge]

thread is dead, should be deleted :[

too much garbage posts/plant pics/plant talk in it... this is the fuckin CONCENTRATES forums!!! I know its your thread, but lets at least try to keep it on topic. lots of good info in here, but even more pointless posts that no one cares about!!!

 

[Guzias1]

too much garbage posts/plant pics/plant talk in it... this is the fuckin CONCENTRATES forums!!! I know its your thread, but lets at least try to keep it on topic. lots of good info in here, but even more pointless posts that no one cares about!!!

dead to me

patience

 

[650baquet]

I feel like it is just a few of us on this thread...but i really like communicating with you on this thread and to tell you the truth this thread has decent amount of traffic here in the concentrate section.

Ended up getting everything at ACE after wasting time driving around to every thrift store coming out empty handed...$20 pot, $6 gasket, $6 drill bit, $3 hose clamps, $2 rubber washers, $3 tube connector and nut, $4 bolts and wing nuts. For me it was $44. Not cheap but same price as the pressure cooker...I also needed to but the drill bit others might already have one, hose clamps might not be necessary for everybody...
i did however stop in at one thrift store i never have and found these Wok for 6.95 and griddle for 3.95. Haven't tested them yet but i'm actually hoping to use the wok for my hot oil baths depending on how consistent it keeps temp. I'm also curious about the dead zone with the griddle but it will be nice i'm sure.

Can't wait to finally piece the distiller together and giver her a try. ....i think i'm going to place a round glass dish in the bottom of the SS pot to distill off the everclear in so it'll be easy to scrap.

I'll be back soon!...i swear lol

 

[650baquet]

Maybe I will keep posting all my distilling shit in my one thread about DIY distiller https://www.rollitup.org/concentrates-extracts/649271-diy-distiller-recovering-ethanol-qwet.html

 

[Guzias1]

I feel like it is just a few of us on this thread...but i really like communicating with you on this thread and to tell you the truth this thread has decent amount of traffic here in the concentrate section.

View attachment 2642154Ended up getting everything at ACE after wasting time driving around to every thrift store coming out empty handed...$20 pot, $6 gasket, $6 drill bit, $3 hose clamps, $2 rubber washers, $3 tube connector and nut, $4 bolts and wing nuts. For me it was $44. Not cheap but same price as the pressure cooker...I also needed to but the drill bit others might already have one, hose clamps might not be necessary for everybody...
View attachment 2642156i did however stop in at one thrift store i never have and found these Wok for 6.95 and griddle for 3.95. Haven't tested them yet but i'm actually hoping to use the wok for my hot oil baths depending on how consistent it keeps temp. I'm also curious about the dead zone with the griddle but it will be nice i'm sure.

Can't wait to finally piece the distiller together and giver her a try. ....i think i'm going to place a round glass dish in the bottom of the SS pot to distill off the everclear in so it'll be easy to scrap.

I'll be back soon!...i swear lol

ahh yeeees. a tiny 2.5 quart pressure cookers costs me $40 plus around here... you did well my friend.. that gasket fits ehh?? lucky find. pshh

there are always random people liking this thread, i wish they would post more results and discussion! as fun as experiments are, they are expensive! even if people posted fails (with a details) , that would still help us all out..

dont be so shy guys

 

[Guzias1]

Maybe I will keep posting all my distilling shit in my one thread about DIY distiller https://www.rollitup.org/concentrates-extracts/649271-diy-distiller-recovering-ethanol-qwet.html

you should post on both of these threads! i dont look at the other one as often and we are right in the middle of ethanol on this thread..
:]

 

[650baquet]

you should post on both of these threads! i dont look at the other one as often and we are right in the middle of ethanol on this thread..
:]

Ya...can you rename this thread??? Maybe "Solvent Solutions" or "Solved Solvents"...am i trying too hard lol

 

[Guzias1]

this thread is out of my hands, i can just spam it

 

[650baquet]

Spam!!!!!!

 

[650baquet]

ok so the nut i bought fit at ACE but the lady said hey let me go get you a single one so you dont have to but a 3-pack. but i think the single one she grabbed wasn't the right size...oh well ACE is only a few blocks away.

 

[Guzias1]

so here my latest winter.
never took any measurements, we'll just see how it turns out.

re ran about 5oz worth material, 3 cans of tane
into pyrex, boiled off tane, till thin film, added everclear
freezer for 48 hrs, mixed a couple times
wallaaaaaa

that filter really filled up with grime..
andd.......................
most importantly, the bowl is just about to be smoked, right after the post :]

 

[vacpurge]

I like how all 3 of us have 1-2 winterizations under our belts and we were all too excited/new to it to get any weight results. not that its really any harder, and im sure we will all do it on our 2nd or 3rd attempts.. I just find it interesting that all 3 of us didnt on our very first try. obviously had other priorities like getting the process right I guess. the weights are just a little side bonus for the "experienced" I guess

I got butane and the weekend off... ill get some pictures.

I also encourage you guys to maybe try pouring your butane INTO the water (hot or cold, im not too sure).. id imagine hot would purge it better though. . your butane level would be near 0 afterwards but the water would be very high.. thats easy to get out. maybe its different than our normal way whereas water in oil is near 0, but the butane is pretty high.

 

[Guzias1]

i hate scraping

ill give that water idea a try.. id spray directly into water. gather, and throw into vacuum , try and get a solid muffin, no heat.. water should escape eventually. i wonder if it will have a water like taste.. hmmmm (wait a minute.... this is if you arnt winterizing ..)

and regards to weighing, im just trying to figure out wtf to do still! i guess i could weigh a clean filter, and weigh the dry winter filter, ya!

im approaching the scrape point,