Club Vert(600)

Dr.D81

Well-Known Member
I run bare bulb, and to do that you just need to move sufficient are through your room. I run a 6 in inline fan and have no problems. When i add another light i will order i peace of glass tube long enough to hold both lights so i dont loose light between the two bulbs like you will with two cool tubes stacked.
 

Dezracer

Well-Known Member
I really need to take some time and rearrange my fan and exhaust ducting. It's longer than it needs to be and has an extra bend in it I'd like to get rid of. I just need to move the fan so that it's between the cooltube and the flange on the wall. Right now the ducting goes towards the door and then curves back the opposite direction to hit the flange on the wall. I bet my temps would go down a little if I fixed that. It would be shorter and straighter shot from the light to the wall.
 

Dr.D81

Well-Known Member
I bet it would do a lot. JD broke the math down one time and you would get a lot more air movement minus the extra bends. It was so much i am putting my air filtration on a sand to get rid of the extra ducting and bends in my room:-)
 

Dezracer

Well-Known Member
My temps are good right now but a little lower would be nice too. Hottest months of the year and my room doesn't seem to ever get over 80. It's typically around 76-78 during lights on.
 

Dezracer

Well-Known Member
ouch! That is hot and would cause heat stress without pumping in co2. We had some heat stress at my buddy's place because he insisted on running his lights during the day and his grow is in the hottest room in the house. Now his lights are on at night and his temps are much better in the flower space. He's at least staying in the 80's now and will be upgrading his fan when we build his vertical setup/
 

Javadog

Well-Known Member
There was a very simple formula that converted "bend"
into "length", allowing one to compute the "effective length"
of a duct-run.

This would allow one to select a fan to meet a flow requirement.

...but, for you, it suffices to say that any straightening will
result in better air flow, all other things being equal.

JD
 

ImGrowingWeed

Active Member
Can you vertical grow with a bulb on both sides of the plants? I mean like a 400 in each circle and 400s in between the circles...sounds like it would blow em up
 

beeralot

Well-Known Member
good question as i am about to go vert well its already started any who this is what i got for space.7 x 2.5 x 7 ft tied back to the walls when they start first time at this hope it goes well. I hope its ok to post here. its a 600 :) and a 400 if i can control heat.
 

Attachments

Dr.D81

Well-Known Member
I have them tyed back with hemp twine:-) i am toping them and cloning to night if i can get my eye to stop herting. I got some fine plywood bust in it today
 

Javadog

Well-Known Member
Few things are rougher, and less appropriate for the eye, than sawdust.

Check it in a microscope some time. Ugh.

Flush and wait for the effect to subside.

JD
 

Dr.D81

Well-Known Member
:-) Took a shower and i fill 100 % better so i guess off to the store for peppers and clone clone clone:-)
 

Dr.D81

Well-Known Member
I flushed like 10 times it was of one of our saws that turns some rpms and it makes super fine dust and that shit would not come out. This is the one that is to blameIMG_20140810_145800.jpg
 

Dr.D81

Well-Known Member
I did but it is scratched i think. It is swollen this morning and it still hurts. I picked up some high dollar eye drops this morning and they are helping some. This is not the first thim i have had this happen it was just so fine it wouldnt come out. I still got 24 purple wreck clones taken, and i am about to go and take some more. Today i will get the rest and rearrange, so i can fit the pw mom in there. It is in the led flower cab now, and i want to chang it out all at one time. I need to work on it before i fill it up again:-)
 
Top