COB LED DIY Build Journal

Yeah aluminum gets eaten by a lot of other metals or chemicals. I'm sure it's fine, AS website might mention it. I know the liquid silver pro would eat the fuck out of it.
 
BM9AGS said:
Yeah aluminum gets eaten by a lot of other metals or chemicals. I'm sure it's fine, AS website might mention it. I know the liquid silver pro would eat the fuck out of it.
Click to expand...

I just found this post from Robin at Northern Grow Lights.

https://www.rollitup.org/t/diy-pass...st120-and-sst140.906729/page-11#post-12754700

The pads I have from Cutter are graphite. I'm wondering if I might have a corrosion issue now with the raw sanded heatsinks. I wonder if I should let the heatsinks sit out for awhile before mounting the COBs, that way it would give the raw aluminum time to develop a layer of aluminum oxide, which would protect it from corrosion.

Or I could look into anodizing the aluminum. I think you can get DIY anodizing solutions.
 
I just spoke with an anodizer here in town. It sounds like they can anodize four heatsinks for around $30. That's not terribly expensive. I might go ahead and do that for some additional piece of mind. I'm putting in all this effort to build this light and it would be good if I don't have any corrosion in the near future. That would completely piss me off. I like doing things right better than doing things over.
 
Well, no surprise that I've run into a few minor issues with my build. As a first build and one-off design, I was bound to run into some problems. I cut my fan holes a little bit too large and was having some trouble aligning the fan holes with the COB holes. They were slightly misaligned. So, I needed away to adjust the COB engines and get them centered between the two holes. I decided to use some scrap 1/8" acrylic sheets and bolt the COB engines to the acrylic. This allows me to adjust the location of the COB engines. I'll bolt the acrylic sheets to the fan grill bolts in order to fasten the COB engines to the metal enclosure.
 

Attachments

  • image.jpeg
    image.jpeg
    709 KB · Views: 138
  • image.jpeg
    image.jpeg
    789.3 KB · Views: 141
  • image.jpeg
    image.jpeg
    1.1 MB · Views: 139
  • image.jpeg
    image.jpeg
    677.8 KB · Views: 144
The acrylic plates really helped me be able to center the COBs properly in the holes. I cracked one plate as I was drilling it, hence the one plate in a different color. The COB, heatsink, fan assemblies are now all bolted to the metal enclosure. Time to wire everything up now.
 

Attachments

  • image.jpeg
    image.jpeg
    1.3 MB · Views: 102
  • image.jpeg
    image.jpeg
    838.4 KB · Views: 94
  • image.jpeg
    image.jpeg
    882.3 KB · Views: 93
PDX Joe said:
The acrylic plates really helped me be able to center the COBs properly in the holes. I cracked one plate as I was drilling it, hence the one plate in a different color. The COB, heatsink, fan assemblies are now all bolted to the metal enclosure. Time to wire everything up now.
Click to expand...
As far as cracked plates you mean on the fan?
 
Last edited:
PDX Joe said:
The acrylic plates really helped me be able to center the COBs properly in the holes. I cracked one plate as I was drilling it, hence the one plate in a different color. The COB, heatsink, fan assemblies are now all bolted to the metal enclosure. Time to wire everything up now.
Click to expand...
You've got your fans sucking air from the top ON TO THE heatsinks right?
 
That light should be an ass kicker. The spacing is how a fixture actually Should Be. Haha. You'd really killed it with 72v cxb3590's.
 
Airwalker16 said:
That light should be an ass kicker. The spacing is how a fixture actually Should Be. Haha. You'd really killed it with 72v cxb3590's.
Click to expand...

Thanks. I actually drafted out the closet size, fixture height and light pattern in AutoCAD to figure out the light spacing. I wanted to try and get the most even light coverage possible in a 3'x3' closet.

I thought about trying the 72v, but I think at the time I bought my driver there weren't as many driver options for four 72v versions. But, I may be misremembering, because I bought the driver about 8 months ago.

Summer has slowed me down a bit. But, I'm hoping I'll have the closet up and running this fall.
 
I've completed most of the wiring. However, I had some trouble soldering wires onto the IEC 320 plug module. The lugs are just too close together for soldering easily. So, instead I think I will use crimp on female terminal connectors for this portion of the wiring. I soldered a 10k resistor to the dimming pot and that went okay. I'm very close to firing this thing up.
 

Attachments

  • IMG_3186.JPG
    IMG_3186.JPG
    1.4 MB · Views: 149
  • IMG_3185.JPG
    IMG_3185.JPG
    1 MB · Views: 137
@PDX Joe it looks like you didn't tin the wire on the resistor. Get a good amount of solder on both before you try to solder them together. Also make sure the tip of your soldering iron is very clean. I found even a slightly dirt tip doesn't transfer the heat well.
 
nevergoodenuf said:
@PDX Joe it looks like you didn't tin the wire on the resistor. Get a good amount of solder on both before you try to solder them together. Also make sure the tip of your soldering iron is very clean. I found even a slightly dirt tip doesn't transfer the heat well.
Click to expand...
Thanks for the tip. This was my pre solder mockup. The soldering went well and I got good solder coverage across the entire wire connection.
 
You must log in or register to reply here.
Back
Top