LED strip gurus around here? Stop by and check out this vertical setup that needs tweaking!!

This is for the guys just joining us I really appreciate you all tuning in

Will look something like this

Here’s something to consider. You mentioned having the lights “spinning” keep in mind that is an intricate hanger to allow adjustment and spinning. Also keep in mind each light has a power cord so up will need to find a way to allow the power connections to spin with the lights. Also make sure the motor has speed adjustments with a knob to control the speed

Also I keep seeing you mentioning exact numbers for plant height after after stretch and very exact plant measurements.
Which strain to you plan to run? As every strain has different height and spacing needs as well as a training method best suited to the strain

One last thing. You say commercial grow system. Just want to point out 2 points.

1) if you want to sell to black market growers they most tend to love their HPS

2) if you want to sell A true commercial piece of equipment everything you use for materials will have to be of proper grade (food grade) which means most DIY products won’t cut the bill. And also make sure any light fixture you design you get proper UL certification or any real commercial facility won’t buy it for liability and insurance reasons

I would build it at first with 2 HLG-320's just for the case you really need up to 700w. If you can get away with only one driver and half as much light, perfect. In this case you already have another driver for a 2nd tower.
Usually we calculate 30-35w/sft to get 800-900μMol/s/m² at 12-16" distance. With 6-8" distance you'll see for sure +1000μMol/s/m² which is enough to add CO² to make better use of the light. With no CO² I would stay with 800-900μMol/s/m² to not stress them plants too much.

I would also LST them to at least 4 or more equal branches cause with single cola plants you don't get a closed canopy covering all the available space. The gaps between the tops would get wider and wider the higher the plants grow. Maybe its best to FIM them as soon as they have etabilished to create lots of twigs. But you would need at least a week or so to veg them a bit before you push the bloom switch.

The more I think about these towers the more I like the idea. I like the saying, "there is always enough space also in the smallest hut" and with this setup one can use the available space to the highest degree.

I've also though about a vertical system as the F-series strips came up(2017) but to mimic a HPS-system with center cooltube.
I thought about covering all 4 sides of a 4ft, 6x 6" alu tube with lots of double row F-strips. The inside of the alu tube gets additional U-channels glued on over the whole length to create lots of 1" high fins inside the tube to allow better heat convection. 6" fans on each side in push/pull configuration to blow air thru the tube. 3 DR F-strips on each side of the tube, 12 strips total, driven by 2 HLG-600H-48B to make it dimmable down to off.
Would be a fecken bright 4ft "360° bulb" with ~1300w LED which could replace 2 vertical 1000w bulbs easily. Easier to hang up and rotate it and you add a trellis in a certain distance to the tube(20" to all sides maybe). One could arrange the plants around the trellis and let the twigs grow thru it. So exactly the opposite of what you plan to realize..

One could also create smaller tubes with less strips. Cooling works pretty good this way cause you need only ~20cm² per LED watt with active cooling and without lens covers half of the heat will be dissipated on the outside anyway so 10cm²/w on the inside is already enough to keep the tube well below ~50-60°C. And cause the plants are arraged around the tube you can easily LST them without doing any changes with the setup. Access from all sides every time but the plants needs to grow big with such a system to create a closed canopy around the bulb before you push the bloom switch.
So its more a setup for growers having only a licence for a limited number of plants.

I’m just trying to figure out why your reinventing the wheel. The most efficient way is having the light in the middle with the Planta surround the light

@Sparky123 I am 100% sure the quality this way will me more appealing and there is no limited space for plants to reach out.. easy visualize and touch ALL plants... No hot spots more uniform grow.. YES I also believe I will yeild slightly more with the bulb in the center but at a cost of more equipment to set up.. & less efficiency as I will have to keep wattage higher since bulbs will be further away

Im using LED so lol it's kind of different thing than standard cmh hps

Actually it probably would be overall cheaper for me to just buy more PVC to put around one light source vs buying multiple lights to put around one PVC ..

You will definitely fill a canopy way faster with 4 walls filled with PVC vs one .. More clones to make it work and now plant training kind of sucks cause you can't really get in there

Sir420 said:

@Sparky123 I am 100% sure the quality this way will me more appealing and there is no limited space for plants to reach out.. easy visualize and touch ALL plants... No hot spots more uniform grow.. YES I also believe I will yeild slightly more with the bulb in the center but at a cost of more equipment to set up.. & less efficiency as I will have to keep wattage higher since bulbs will be further away

Click to expand...

I think you will be more expensive this way. More or less your making a verttical system with a light mover. I’ll like to seethe retail of this vs the volksgarden

I guess it's as simple as pulling the PVC back & working away... Then closing it back up...hmmm

But as far as the scrog & canopy training like garden fencing will make it hard to just pull in & out like that..