tekdc911
Well-Known Member
well it would sound really bad if you were making ediblesI should be ripping on some COC. (That just doesn't sound right.) .
well it would sound really bad if you were making ediblesI should be ripping on some COC. (That just doesn't sound right.) .
the ones i ran 12/12 fs were tall they still veg'd for a while before they finally flipped , should be alot of semi auto's in there i bred the ones that flowered on just over 14/10 some tried to flower on 16/8 i just slowly cut the lights back and then made my choices by when they started to flower ...... attempting to get 24/0 veg and like a 16/8 flowerTek - I haven't popped any of those yet. They are next in line. RIGHT NOW I can only run them under 12/12. I suppose I could pop 3-5 and do 12/12 from seed. I have some extra light now.
It's really time for me to make a nice veg room.
What are you using for your main flower room light/lights?
Yea, some strains are more resistant to reversal than others. 25ppm should be good enough to flip anything tho, if you spray 2-3x daily, and cover the whole plant. That's the benefit of homemade/well made cs. You can spray the entire plant, leaves, buds, and stems, and it won't burn at all. It'll just end up growing and looking like a male, as opposed to some deformed abomiation with a a mix of burnt pistils and some pollen sacs.ive actually used 15 ppm and it worked fine once and then the next time i had to use something stronger .......
Hey, I was doing some editing on it. I'll pm it to you tho now so you can get started.Hazy,
I was getting ready to read your link to CS and it shows a "rollitup error" thread could not be found. I think I'm ready to make my own. Is the thread/link gone or hosed?
Hazy,
I was getting ready to read your link to CS and it shows a "rollitup error" thread could not be found. I think I'm ready to make my own. Is the thread/link gone or hosed?
Colloidal Silver Guide posted.Shit let me get in on the CS I'll give it a go haha
Yea, I fixed the link in my sig too lolI'm going to go check it out. The link at the bottom works too. Nice.
Just sure they are .9999 pure. Also, not everyone cleans the electrodes very often, but it helps keep your cs clear, and full of microscopic particles, instead of larger bits of silver that just sit on the plants surface and potentially suffocate it, possibly causing some deformation. Ideally, cs should look exactly like water until you shine a light through it. It can still work if it isn't perfect, but it works best and most efficiently when made with more care,i just bought 2 x 1 gram bullion coins off of ebay it was like 12 bucks roughly its been a while ago and just alligator clipped them .... the cleaning the silver off every few minutes only needs to be done if you are taking the CS i just let it go over night with 3 9 v batteries and there was all kinds of black nasty flakes but it didnt effect the usability of it i just siphoned it out and left the bottom junk layer in the jar i made it in
ya its as pure as you can get ......... the larger flakes fall to the bottom ...... when your PPM gets in the 300 + range is when they start cooking ...... well had some cook around 150 PPM but they still flipped so whats it matter what the branch that was sprayed looked like[QUOTE
Yea, I fixed the link in my sig too lol
Just sure they are .9999 pure. Also, not everyone cleans the electrodes very often, but it helps keep your cs clear, and full of microscopic particles, instead of larger bits of silver that just sit on the plants surface and potentially suffocate it, possibly causing some deformation. Ideally, cs should look exactly like water until you shine a light through it. It can still work if it isn't perfect, but it works best and most efficiently when made with more care,
the beans you showed me should pop i ran a test batch from almost all i had the kc45 BC is still up in the air the jdp x should pop with little issue but they take a while ....... none F2's hazes came up all rotted so ill run another batch and see what i can tell ......... not sure what you have honestly but some may not come up at all from what i can tell so far ......... even the good looking beans mottled/ big and brown didnt even try i scraped the seam on some and manually cracked them after a soak and still nothing ......... so i dunnoDay 15 of misting -
3/31/15
Well I ran out of TM today. I used up the 1 oz bottle plus another little bit of another. Here it is today. Just trying to keep it low. I can't get a good pic of the pistils but they appear to be somewhat browning and there aren't many of them. It could be I sprayed directly on the pistils and it burned them or it's working like it should. Just a waiting game now. Here it is today.
View attachment 3385272
niceMy daughter was cleaning out her room and was going to throw this away. Hell no!! If it doesn't work as a mobile scrog unit, at least it gives me some other ideas.
View attachment 3385273
+ this
View attachment 3385274
= this.
View attachment 3385275 View attachment 3385276