Hey, great read here! Thanks for all the testing and feedback and deets.
I was all ready to scale up my chinese chip DIY LEDs and ready to go the Vero 29 route, until I fell into this thread.
I was all set to build a 2 chip setup for my 2ft x 2ft x 3ft tent. But I'm liking the bang/buck/efficiency of the 4x CXB3590 + MW HLG-185H-1400B combo, and running it at a lower wattage...even possibly passive?
I was just planning to run 4x Arctic hs/fans, but, if I can avoid that and run a large passive design, that I could add a 120mm fan or two for higher power as needed.
What HS size could you suggest for this sort of setup and size constraint. Should I stick to 2 chips on individual 60w or 80w drivers for this space? A passive design could also keep the profile much smaller, and allow for more vertical space as needed with my 3' limitation.
Ready to get some parts ordered from KB asap, likely going with the 3000k chips that are in stock. Do they also carry the wire connectors, or do I have to source those elsewhere?
This is a copy/paste from another thread o here
@45.7%
(2) CXB3590 3500K CD 36V @ 2.5A (91.65W ea) $95
(2) HLN-80H-36A $90
183 dissipation W -> 99.37W heat
(2) Arctic 64 Plus CPU coolers $26
(2) lenses $8
83.63 PAR W covering 5 ft² = 749 PPFD
$219 = 2.62/PAR W
@49.7%
(2) CXB3590 3500K CD 72V @ 1.05A (75.5W ea) $95
(1) HLG-185H-C1400 (running at ~1050mA) $65
151 dissipation W -> 76W heat ->
passive cooled heatsink 9120cm² -> (2) 10"X10" heatsink $75
or
active cooled heatsink 3040 cm² min -> 3.5" X 30" heatsink (for spread) $40 + 80mm fan+psu $10
or
(2) Arctic 64 Plus CPU coolers $26
(2) lenses $8
75 PAR W covering 4ft² = 840 PPFD
75 PAR W covering 5ft² = 672 PPFD
$243 = $3.24/PAR W passive cooled
$218 = $2.91/PAR W active cooled on bar heatsink
$194 = $2.59/PAR W active cooled on CPU coolers (uniform spread, best value?)
@ 56.3%
(4) CXB3590 3500K CD 36V @ 1.4A (49W ea) $190
(1) HLG-185H-C1400 $65
196 dissipation W -> 85.7W heat ->
passive cooled heatsink 10284cm² -> 5.88" X 38" heatsink $72 (could split in 2 to improve uniformity/spread)
or
active cooled heatsink 3428cm² min -> 3.5"X36" heatsink (for spread) $45 +80mm fan +psu $10
(4) lenses $16
110.3 PAR W covering 6ft² = 824 PPFD
$311 = $3.07/PAR W passive cooled (great value point IMO, very efficient use of driver)
$326 = 2.96/PAR W active cooled
@61.2%
(5) CXB3590 3500K CD 36V @ 1.05A (35.5W ea) $237.50
(1) HLG-185H-C1050 $65
177.5 dissipation W -> 68.9W heat ->
passive cooled heatsink 8268cm² -> 4.9"X36" $70
or
active cooled heatsink 2756cm² -> 3.5"X36" heatsink (for spread) $45 + 80mm fan + psu $10
(5) lenses $20
108.63 PAR W covering 6ft² =
$392.50 = $3.61/PAR W passive cooled
$377.50 = $3.48/PAR W active cooled
@64%
(8 ) CXB3590 3500K CD @ 700mA (23W ea) $380
(1) HLG-185H-C700 $65
184 dissipation W ->66W heat ->
passive cooled heatsink 7920cm² -> 4.23"X44" $68 (could split these into 2 or 4 units)
or
active cooled heatsink 2640cm² -> 3.5"X36" heatsink (for spread) $45 + 80mm fan + psu $10
active cooled heatsink 2640cm² -> 1.8"X44" heatsink $34 + 80mm fan + psu $10
(8 ) lenses $32
117.8 PAR W covering 6ft² = 879 PPFD
117.8 PAR w covering 7ft² = 754 PPFD
$545 = $4.63/PAR W passive cooled (great option if your area is high electrical cost, Hawaii, NYC, SoCal etc or if your grow is already heat limited and you want to increase yield without running more AC, ducting and fans)
$532 = $4.52/PAR W active cooled 3.5"
$521 = $4.43/PAR W active cooled 1.8"