Can anyone send me a link where to buy canning jars with no shoulders?
- Thread starter estesj
- Start date
mogascreeta
Active Member
wal-mart dude
estesj
Well-Known Member
Those ones in the pic are from wallmart.com
ndangerspecimen101
Well-Known Member
a little shoulder wont hurt.... but you don't wanna get total hutch back jars! Just a little tap on the bottom and POOF their out!
estesj
Well-Known Member
So those wide mouth ones in my pic are good to go?
ndangerspecimen101
Well-Known Member
those would do fine my friend!
Just make sure the clean the rim out good before and after you fill your jars with the much needed vermiculite/BRC MIX!
Just make sure the clean the rim out good before and after you fill your jars with the much needed vermiculite/BRC MIX!
estesj
Well-Known Member
Cool. I was told to put the verm layer on the bottom of the jar my the famous ANC.
estesj
Well-Known Member
Remember you said To put a layer of verm on the bottom of the jar with my wbs? I dont have to sterilize that do I? The pc should do that right?
estesj
Well-Known Member
Yea i'm gona use tyvek too. They are ready to inject the next day after pc'em right?
A layer about as thick as the tip of your little finger...
And also a pic of how to make an easy lid, polyfill from petshop, (NOT COTTONWOOL), you just inject straight through it, flameing the needle between doing each jar.
blaze1camp
Well-Known Member
ANC
Well-Known Member
yeah they are normaly cool enough in a half a day's time.
I like to let them sit for 4 days or so to show any possible contaminated jars... before injecting.
if they then contaminate I know the problem was with the syringe rather than second guessing my whole process up to that point.
I like to let them sit for 4 days or so to show any possible contaminated jars... before injecting.
if they then contaminate I know the problem was with the syringe rather than second guessing my whole process up to that point.
ANC
Well-Known Member
if shit grows in there that you didn't inject, its contaminated 
If you do go for the cambos' they are trickier as they myc is not always all white like with cubensis strains, and can resemble that grey cotton mold you sometimes get.
Next time you go to the shop, pick up a packet of button mushrooms and give it a good smell, that is the smell yo uwant when you eventualy open your jars, any cidery or sour smells comming from your jars, and you throw them out outside, downwind with your nose and mouth covered.
If you do go for the cambos' they are trickier as they myc is not always all white like with cubensis strains, and can resemble that grey cotton mold you sometimes get.
Next time you go to the shop, pick up a packet of button mushrooms and give it a good smell, that is the smell yo uwant when you eventualy open your jars, any cidery or sour smells comming from your jars, and you throw them out outside, downwind with your nose and mouth covered.
estesj
Well-Known Member
Cool man. I hope for the best for no contams but thanks for the signs. Some people say give the jar a shake right after you inject them and others say wait til they are 30% colonized. What do you say?if shit grows in there that you didn't inject, its contaminated
If you do go for the cambos' they are trickier as they myc is not always all white like with cubensis strains, and can resemble that grey cotton mold you sometimes get.
Next time you go to the shop, pick up a packet of button mushrooms and give it a good smell, that is the smell yo uwant when you eventualy open your jars, any cidery or sour smells comming from your jars, and you throw them out outside, downwind with your nose and mouth covered.
ndangerspecimen101
Well-Known Member
so not even a little shoulder would work?
ndangerspecimen101
Well-Known Member
Ahhhh those jars you depict there look exactly like the ones I bought.... I should not have any problem sliding those puppies out 
Similar threads
