New Experimental Advanced DIY Designs.

stardustsailor

stardustsailor

Well-Known Member
Until ,savings will allow for something better ....
One has to keep experimenting (and growing ) with what he has ....

So ..Next project ...

""Summerlight " ....

6 panels ...

( 150 Watt total at plug-drivers included. ~25 Watts per panel . )

Each panel .... :

16 x WW ( 2500-2700 K )
4 x red 620-640 nm
2 x NW ( 4500-5500 K )
1 x red 650-660 nm
1 x violet 395-410 nm



Spectrum (approx) :summerlight spectr.JPG

The panels :
Project Summerlight.jpg
 
PetFlora

PetFlora

Well-Known Member
[h=1]Sacred Geometry 101D: Concentric Circles
[/h]http://www.youtube.com/watch?feature=endscreen&v=D39eGrx3a_A&NR=1

Advance to roughly 2:30 Seed of Life, Tree of Life and Flower of Life, which is THE key, and then there's Metratron's Cube
 
stardustsailor

stardustsailor

Well-Known Member
...

Designing Astir's 'flagship'.....


Some details :
-Full aluminium construction .
-96 x Osram SSL oslon 80 . (350-550 mA )
-All electronics fuse protected (x2 )
-Special relay circuit .If fan(s) fails ,leds switch off.
-MeanWell drivers (x4 )
-Emb papst 120 mm Fans (x2 )
.....


new 4 x 24 iso 1.jpgnew 4 x 24 iso 2.jpg
new 4 x 24 cover off.jpgnew 4 x 24 iso xray 1.jpg
new 4 x 24 iso xray 2.jpgnew 4 x 24 iso xray 3.jpg

new 4 x 24 iso 2xr.jpgnew 4 x 24 iso xray side.jpg
new 4 x 24 iso xray 4.jpgnew 4 x 24 iso xray bw.jpg
 
PetFlora

PetFlora

Well-Known Member
How about angling the switches to 45*s for easier access. Also looks like the power cords will be in the way if kept where you have them
 
stardustsailor

stardustsailor

Well-Known Member
PetFlora said:
How about angling the switches to 45*s for easier access. Also looks like the power cords will be in the way if kept where you have them
Click to expand...

45 degrees ...? ..
Nope ....Too complicated design (in manufacturing..=>higher cost -....already way high ....-

No cords there ...Neither drivers ....
Early blueprints ...
Only basic design ,fans,fuses and switches ...
Cord will be on top ...(cord for mains ) ....

Anyway....Thanx 4 the remarks ....
 
stardustsailor

stardustsailor

Well-Known Member
Spectrum ....

4 led pcbs ...

(50 x 60 mm )

Each having 24 pcs of leds ....

16 x Warm Whites 2700 K of the LCW CQ7P family ....
4 x Neutral Whites 5000 K ,also,of the LCW CQ7P family ....
4 x LH CP7P 645-660 nm hyper reds ...

On each heatsink ,2 x 24 led pcbs .....

led engine ssl 24 on heatsink.jpg

(Exact led types,will remain a small " trade " secret ...)
 
ganja 2

ganja 2

Active Member
maybe the 4 switches should be placed at the side and not at the top cause they will be diffycult aproaced when the panels will be hanged at 2 metres high for example...
 
PetFlora

PetFlora

Well-Known Member
stardustsailor said:
45 degrees ...? ..
Nope ....Too complicated design (in manufacturing..=>higher cost -....already way high ....-

No cords there ...Neither drivers ....
Early blueprints ...
Only basic design ,fans,fuses and switches ...
Cord will be on top ...(cord for mains ) ....

Anyway....Thanx 4 the remarks ....
Click to expand...
You are missing it. It is not complicated. SIMPLY turn the switches 45*, otherwise, one switch is directly behind the other and hard to reach over

 
PetFlora

PetFlora

Well-Known Member

I would like to see the diodes configured in Merkaba clusters, with 1 NW in the center, surrounded by WW- OK, maybe you don't this BUT...

If the NW was a 3w diode and the NW one watt diodes, the NW could be on its' own dimmable circuit. More during veg, less during flower
 
stardustsailor

stardustsailor

Well-Known Member
PetFlora said:

I would like to see the diodes configured in Merkaba clusters, with 1 NW in the center, surrounded by WW- OK, maybe you don't this BUT...

If the NW was a 3w diode and the NW one watt diodes, the NW could be on its' own dimmable circuit. More during veg, less during flower
Click to expand...
No need for that ..
This light's spectrum covers everything ....
 
stardustsailor

stardustsailor

Well-Known Member
....

relay fan fail safe circuit.jpg

As long as fan operates ,relay stays closed and mains power pass through relay,to fuse to led drivers ...
(relay has to be cooled ..attached to alum surface ... )

If fan stops working ( fails ) ,relay 12 V circuit opens ,so does the mains circuit to led drivers ..
Power is cut-off ...
Leds are switched off ..
New fan has to be installed for the leds to switch on again ....
(or by ' overriding ' the " Fan-Fail-Safe" circuitry ....with a single ' bridge ' )
 
tolakra

tolakra

Member
It could have a hole (with screen-σίτα) above the drivers-between the fans, so that the heated air around the drivers isn't trapped in there.
The fans are blowing air in the panel right? The air will get away through the sides of the panel as well as trough the center of the panel.
If there isn't a hole in there, the center of the panel will not be cooled right
 
stardustsailor

stardustsailor

Well-Known Member
tolakra said:
It could have a hole (with screen-σίτα) above the drivers-between the fans, so that the heated air around the drivers isn't trapped in there.
The fans are blowing air in the panel right? The air will get away through the sides of the panel as well as trough the center of the panel.
If there isn't a hole in there, the center of the panel will not be cooled right
Click to expand...
Yeap.....


new 4 x 24 ram air.jpgnew 4 x 24 ram air1.jpgnew 4 x 24 ram air2.jpg
 
You must log in or register to reply here.
Top